Requirements
–
PC (Windows 7 and later) with Ethernet interface
–
Components for network connection
–
Programming software CODESYS V3
–
Package CPX-E-CEC compliant with firmware of product
Preparations
The user requires administrator rights to install and operate programming soft-
wareCODESYS V3.
1. Install CODESYS V3.
2. Start CODESYS V3 with administrator rights.
3. Open Package Manager
è
menu command [Tools] [Package Manager].
4. Install the current package for CPX-E-CEC
è
online help for CODESYS V3
è
“Package Manager”.
5. Restart CODESYS V3 in order to use the new package.
6. Connect the controller to the network connection [ETH
1] or [ETH
2] through a
switch/hub or directly to the PC
è
8.1 Network.
7. Adapt the network settings
è
menu command [Online] [Scan Festo Devices]
è
online help for CODESYS V3
è
“Scan Festo Devices”.
The current version of the package CPX-E-CEC for CODESYS V3 is available in the
Festo Support Portal
è
www.festo.com/sp.
Further information is available in the product-specific Help
è
Online help for CODESYS V3
è
“Getting started”.
Procedure for unwanted program states
If a program with real-time priority is not responding:
1. Set run/stop switch to stop.
Ä
The boot application cannot be started.
2. Restart the controller.
3. Establish connection to CPX-E-CEC.
4. Delete boot application using “Reset device to original state”
è
General help for CODESYS V3.
10
Service
NOTICE!
Accumulation of heat due to reduced air supply to electronics.
•
Keep the ventilation slots free and regularly remove contamination.
10.1
Firmware service (update)
•
Update the controller firmware with suitable software from Festo
è
www.festo.com/sp.
11
Diagnostics and fault clearance
11.1
Diagnostics options
Various options are available for diagnosing errors:
–
Internal system diagnostics
–
LED indicators on the product
11.2
Internal system diagnostics
The internal system diagnostics is described in the “Description of automation
system CPX-E”
è
1.1 Further applicable documents.
11.3
LED indicators
The module- and network-specific LED displays are described below.
The system-specific LED indicators are described in the documents for the auto-
mation system CPX-E
è
1.1 Further applicable documents.
Module-specific LED indicators
Operation [Run]
LED
(green)
Meaning
Remedy
Lit
CODESYS application is running
–
Off
CODESYS application is not available or
has stopped
–
Tab. 11 Operation [Run]
Ethernet interfaces [LA
ETH
1] [LA
ETH
2]
LED
(green)
Meaning
Remedy
Lit
Network connection established
Status “Link”
–
Flashing
Network connection established
Status “Activity”
–
Off
No network connection
Check network connection.
Tab. 12 Ethernet interfaces [LA
ETH
1] [LA
ETH
2]
EtherCAT interface [LA EC]
LED
(green)
Meaning
Remedy
Lit
Network connection established
Status “Link”
–
Flashing
Network connection established
Status “Activity”
–
Off
No network connection
Check network connection.
Tab. 13 EtherCAT interface [LA EC]
Network-specific LED indicators
Connection status [XF1], [XF2]
LED
(green)
Meaning
Remedy
Lit
Network connection established
Status “Link”
–
Flashing
Network connection established
Status “Activity”
–
Off
No network connection
Check network connection.
Tab. 14 Connection status [XF1], [XF2]
Module status [MS]
LED
(green,
red,
orange)
Meaning
Remedy
Lit up
green
Normal operating status
–
Flashing
green
Configuration of automation system CPX-E
not complete or not correct
Complete or correct configuration of the
automation system CPX-E.
Lit up red
Error cannot be rectified
Contact Festo Service
è
www.festo.com.
Flashing
red
Error can be rectified
Check configuration of the automation
system CPX-E.
