Ferris 5901756 Скачать руководство пользователя страница 36

Страница: 36 / 40

Not for

Reproduction

ferrismowers.com

FAILURE MODE

CAUSE OF PROBLEM

CORRECTIVE ACTION

The strainer or tip is clogged.

Remove the spray nozzle tip. Inspect the

tip orifice and the strainer to ensure they

are not clogged. Clean or replace these

components as necessary.

The filter is clogged.

Remove the sediment from the filter

housing and inspect the filter screen.

Clean or replace the screen as

necessary.

The pump won't operate.

Inspect the pump fuse located in the fuse

box. Ensure that either the spray pump

ON/OFF console switch activates the

pump.

Hoses are kinked.

Smooth out hoses and use wire ties to

make sure that they do not kink again.

Spray tank volume is low.

Refill the spray tank. Note that in very

rough or hilly conditions, the liquid in the

spray tanks may slosh around and the

tank discharge tube may starve when

the tank level is low. This can cause poor

spraying performance.

The engine speed is too low.

Operate the machine at full engine

speed. The spray system is designed

to operate most efficiently at full engine

speed.

The pump is worn or damaged.

Replace the pump.

Electrical System Operates Incorrectly

FAILURE MODE

CAUSE OF PROBLEM

CORRECTIVE ACTION

Battery terminals require cleaning.

Clean the battery terminals.

Battery discharged or dead.

Recharge or replace battery.

Wiring loose or broken.

Visually check wiring and replace

broken or frayed wires. Tighten loose

connections.

Electrical wiring damage.

Locate and repair damaged wire.

Spark plug(s) faulty, fouled, or incorrectly

gapped.

Clean and gap or replace. See

authorized service dealer.

Electrical system does not operate or

operates incorrectly.

Fuse blown.

Replace fuse.

Содержание 5901756









































Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды

Ferris 5901756, Руководство оператора

Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды