Ferris 5901756 Скачать руководство пользователя страница 10

Страница: 10 / 40

Not for

Reproduction

ferrismowers.com

Safety alert triangle.

Go across slopes, not up and down.

Caustic liquid and chemical burn hazard.

Gas inhalation hazard.

Thrown object hazard.

5103184 - Decal, Warning, Rotating Parts

Safety alert triangle.

Amputation - Rotating parts.

Safety Alert Symbol and Signal Words

The safety alert symbol ( ) is used to identify safety

information about hazards that can result in personal injury. A

signal word (DANGER, WARNING, or CAUTION) is used with

the alert symbol to indicate the likelihood and the potential

severity of injury. In addition, a hazard symbol may be used to

represent the type of hazard.

DANGER

indicates a hazard which, if not avoided,

will

result in death or serious injury

WARNING

indicates a hazard which, if not avoided,

could result in death or serious injury

CAUTION

indicates a hazard which, if not avoided,

could

result in minor or moderate injury

NOTICE

indicates a situation that

could result in damage

to the product

Safety Interlock System

This unit is equipped with a parking brake safety interlock

switch. These safety systems are present for your safety, do

not attempt to bypass safety switches, and never tamper with

safety devices. Check their operation regularly.

Test 1

- Engine should NOT start if:

• The parking brake is NOT engaged (unlocked position).

Test 2

- Engine SHOULD start if:

• The parking brake is in the engaged (locked position).

Содержание 5901756









































Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды

Ferris 5901756, Руководство оператора

Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды