manualshive.com logo in svg

Ferris 5901756, Руководство оператора

Поделиться
Скачать
Ferris 5901756 Скачать руководство пользователя страница 18

Not for 

Reproduction

18

ferrismowers.com

Begin with the 

Smooth Travel

 procedure, and then advance

through the forward, reverse, and turning maneuvers. 
Before moving the ground speed control levers you must be

standing on the operator platform and the parking brake must

be disengaged.

Adjusting the Maximum Forward Speed Control

Bar

This unit is equipped with an adjustable maximum forward

speed bar (A, Figure 15) which is located in front of the

ground speed control levers (B & C). The maximum forward

speed bar has an infinite number of adjustment positions to

suit the desired maximum forward speed of the operator.

15

• The closer the maximum forward speed bar is to the

ground speed control levers the slower the unit will drive.

• The further away the maximum forward speed bar is from

the ground speed control levers the faster the unit will

drive.

When learning to drive the unit, it is recommended that

the slowest speed setting be used until the operator is

comfortable driving the unit.

To adjust the Maximum Forward Speed Bar to the desired

position:

1. Bring the unit to a complete stop.
2. Release the cam lever (D).
3. Position the maximum forward speed control bar to the

desired position.

4. Lock the cam lever in place.

Smooth Travel

The ground speed control levers of this unit are responsive.
The BEST method of handling the ground speed control

levers is in three steps as shown in Figure 16.

16

FIRST

, place your hands on the ground speed control levers

and the maximum forward speed control bar as shown.

SECOND

, to go forward gradually push the ground speed

control levers with the palms of your hands evenly towards

the maximum forward speed control bar.

THIRD

, to speed up squeeze the ground speed control levers

to the maximum forward speed control bar. To slow down

smoothly, slowly move the levers evenly towards NEUTRAL.

Basic Driving

1.

To drive FORWARD:

 gradually move both ground speed

control levers FORWARD evenly from neutral. Slow down

and repeat.

17

Содержание 5901756









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды