)+**4
(FTC-1440K2)
14.4 V—
- - -
230 V~
$
50 Hz
/
1.2 Ah (NiCd)
/
3 - 5 #
&
2
!
0-400/0-1150
/
/
0.8 - 10 mm
B !
20 mm
B
10 mm
B
13 mm
8 1.66
kg
Lpa ( )
66.28 dB(A)
< 2,5 m/s
2
. !6'
.
.
#
EN 60335,
$ .
*'!! . 3%
% # !
()
!. ' "
".
.! %'! 3
/
, !
. ! 1.5
mm
2
. O ,
# # .
)+,* **
1
*
2
+
1
P
1
8
2
1
'
1
!
1
' ,
.
)$+4+ * , + )+7+
(.)
1
* /
2
' !
3
' !
4
*! ! (
5
6
+
+)+8 9*,*:
" ,
.
%/! 6! 3%
(.B)
' ,
.
•
S # (5b)
(5a).
•
.
•
$
.
•
S
.
%/! 6! # %#
(.)
•
8 ! (2)
, !
.
•
, ,
. &! ,
90P. &
.
•
% ,
(6)
.
56
Ferm
OPERATION
Always observe the safety instructions and applica-
ble regulations.
Firmly hold the machine and push the bit with even pres-
sure into the workpiece. Do not force the machine.
Use only bits that do not yet show any signs of wear.
Worn bits have a negative effect on the efficiency of the
machine.
ADJUSTING THE SPEED
(Fig.D)
The machine has two different drilling speeds.
•
Set the speed selection switch (3) on position '1' for
drilling at a low speed.
•
Set the speed selection switch on position '2' for dril-
ling at high speed.
TORQUE ADJUSTMENT
(Fig.E)
The machine has different torque settings by means of
which the force for fastening and loosening screws can be
determined.
•
Put the torque setting ring (4) at the required torque.
•
Preferably select the lowest possible setting to move
the screw. Select a higher torque setting when the
motor is slipping.
Screwing screws in and out
•
Set the direction switch (2) on position 'R' for putting
in screws.
•
Set the direction switch on position 'L' for removing
screws.
Drilling
•
Turn the torque setting ring (4) to drilling position.
Be sure that the direction switch (2) always in posi-
tion 'R' during drilling.
SWITCHING ON AND OFF
(Fig.F)
•
Press the on/off switch (1) in. You regulate the speed
of the machine by the degree to which you keep the
switch pressed in.
•
Releasing the on/off switch (1) causes the drill to stop
immediately
•
Slide the direction switch (2) to the middle to lock the
machine in switched off mode.
Do not put the machine away until the machine has com-
pletely stopped running. Do not store the machine on a
dusty surface. Dust particles can get into the mechanism.
CHARGING BATTERIES
(Fig. G)
The enclosed battery charger has been exclusively de-
signed for loading batteries of the FTC-1440K2.
•
Position the battery in the battery charger as indica-
ted in the illustration.
•
Plug in the battery charger. The red “fast charging”
light is then illuminated
•
As soon as the green light is illuminated, charging has
finished and the accumulator is ready for use
Only use the battery charger in a dry environment at
a temperature between 10 °C and 40 °C.
The accumulator on the drilling machine you have pur-
chased is not charged up. Before using it for the first time
leave it to charge for 5 - 7 hours in order for it to reach its
full capacity.
The total capacity of the accumulator will be reached af-
ter it has been charged 4 – 5 times.
Ferm
5