background image

7

EN

to the instructions represented in fig. 2. Place the 
compressor on a flat surface or at a maximum slope 
of 10° (fig.3), in a well ventilated area, protected 
against atmospheric factors and not in explosive 
surroundings. If the surface area is sloping and 
smooth, make sure that the compressor will not 
move when in operation. If the surface area is a 
board or a shelf of a bookcase, just make sure that 
they cannot fall down by securing them properly. 
For proper ventilation and effective cooling, it is 
important that the compressor is positioned at least 
100 cm from the wall (fig. 4). 

 Make sure that the compressor is 
transported in the right way, do not turn it 
upside down and don’t lift it with hooks 
or ropes (fig. 5-6).

filling the compressor with oil.

Your compressor is supplied with oil which is 
already included in the carter.
Before use, remove the transport cap on the carter 
(12), and replace it by the regular oil cap (fig 7).
Before use, ensure that oil level is sufficient. 
This can be checked by checking the oil 
inspection glass (13). When compressor is placed 
horizontally, the oil level shall reach the red mark. 

installing the air filters.

Remove the transport lids and replace them with 
the supplied air filters before using the compressor.

Starting up

•   Check whether the mains voltage corresponds 

to that indicated on the electrical specification 
plate (fig. 10), the permitted tolerance range 
should be within 5%. 

•   Press the switch (3) situated on the upper part 

into the “0” position according to the pressure 
regulator type fitted on the device (fig. 11).

•   Put the plug in the plug socket (fig. 9) and start 

the compressor up by putting the switch(3) 
of the pressure regulator in the “I” position. 
The operation of the compressor is fully 
automatic. The pressure regulator will stop 
the compressor when the maximum value has 
been reached and start it up when the pressure 
drops below the minimum value. Normally 
the difference in pressure is approx. 2 Bar/29 
psi between the maximum and the minimum 
value. For instance - The compressor will stop 

when it reaches 8 Bar (116 psi) (this is the 
maximum operating pressure) and will start 
up automatically when the pressure within the 
tank has dropped to 6 Bar (87 psi).

 The head/cylinder/transmission pipe 
assembly may reach high temperatures, 
so take care when working close to these 
parts and do not touch them to avoid 
burns (fig. 12 - 13). 

adjusting the operating pressure

Fig. 14

It is not necessary continuously to use the 
maximum operating pressure, the compressed-air 
tools often require less pressure. With regard to 
compressors supplied with a pressure reduction 
valve it is necessary to set the operating pressure 
properly. 
It is possible to set the operating pressure by 
using the turning knob(5) on the reduction valve. 
•   By turning clockwise, the pressure will be 

increased.

•   By turning anti-clockwise, the pressure will be 

reduced.

The compressor has two pressure gauges and 
one point to connect an air hose:
•   Pressure gauge (7): The pressure of this outlet 

can be regulated with help of the reduction 
valve (5).

•   Pressure gauge (8): tank pressure 

Hints for accurate adjustment of the pressure 
regulation:
•   Turn the turning knob (5) anti-clockwise till 

pressure is fully released

•   Connect the air tool you want to use to the 

quick coupler (6)

•   Activate the air tool shortly, so the pressure 

gauge (7) will show the right pressure level

•   Turn the turning knob (5) clockwise, till the 

pressure gauge (7) shows the pressure level 
you need

•   Your air tool is now ready to use.

Note: when not connecting an air tool while 
adjusting the pressure, it might occur the pressure 
gauge (7) is not reacting accurately on the 
pressure drop.

Содержание CRM1044





































































Отзывы: