Ferm AGM1131, Оригинальное руководство пользователя

Страница: 9 / 60

9
EN
which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The grinding surface of centre depressed
wheels must be mounted below the plane of
the guard lip.
An improperly mounted wheel
that projects through the plane of theguard lip
cannot be adequately protected.
c) The guard must be securely attached to the
power tool and positioned for maximum
safety, so the least amount of wheel is
exposed towards the operator.
The guard
helps to protect the operator from broken
wheel fragments, accidental contact with
wheel
and sparks that could ignite clothing.
d) Wheels must be used only for
recommended applications. For example:
do not grind with the side of cut-off wheel.
Abrasive cut-off wheels are intended for
peripheral
grinding, side forces applied to
these wheels may cause them to shatter.
e) Always use undamaged wheel flanges
that are of correct size and shape for your
selected wheel.
Proper wheel flanges support
the wheel thus reducing the possibility of
wheel breakage. Flanges for cut-off wheels
may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger
power tools.
Wheel intended for larger power
tool is not suitable for the higher speed of
a smaller tool and may burst.
Additional Safety Warnings Specific for
Abrasive Cutting-Off Operations
Cut-off operations are only suitable with
a special protection guard (not included)
Fig. E2 - F2.
a) Do not “jam” the cut-off wheel or apply
excessive pressure.
Do not attempt to make
an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility
to twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
b) Do not position your body in line with and
behind the rotating wheel.
When the wheel,
at the point of operation, is moving away from
your body, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
c) When wheel is binding or when interrupting
a cut for any reason, switch off the power
tool and hold the power tool motionless
until the wheel comes to a complete stop.
Never attempt to remove the cut-off wheel
from the cut while the wheel is in motion
otherwise kickback may occur. Investigate and
take corrective action to eliminate the cause of
wheel binding.
d) Do not restart the cutting operation in the
workpiece.
Let the wheel reach full speed
and carefully re-enter the cut. The wheel may
bind, walk up or kickback if the power tool is
restarted in the workpiece.
e) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback.
Large workpieces tend to sag under
their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides
of the wheel.
f) Use extra caution when making a “pocket
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can
cause kickback.
2. MACHINE INFORMATION
Intended use
Your angle grinder has been designed for grinding
masonry and steel materials without the use of
water. For cutting, a special protection guard
must be used (not included). Fig. F2.
This machine is suitable for light work.
Do not overload the machine.
Technical specifications
Model No. AGM1131
Voltage 20V
No load speed 8.000/min
Recommended battery CDA1168 20V ~ 4AH
Grinding disc Diameter: 125 mm
Bore: 22.2 mm
Spindle thread M14
Weight 1.22 kg
Sound pressure level LPA 85.5 dB(A), K=3dB(A)
Acoustic power level LWA 96.5 dB(A), K=3dB(A)
Vibration
Main handle 6.162 m/s
2
, K=1.5 m/s
2
Auxiliary handle 5.833 m/s
2
, K=1.5 m/s
2