M U S T A N G
™
F L O O R
2. Stereo PA system: Set Output Configure to "Stereo" and set
Output Voicing to "PA System."
L
UNBALANCED
OUTPUT
t
(OR XLR OUTPUT)
R
UNBALANCED
OUTPUT
t
(OR XLR OUTPUT)
3. Mono PA system -AND- Mono monitor (or combo amplifier): Set
Output Configure to "Mono," then set Right Out Voicing to "PA
System" and Left Out Voicing to "Combo."
L
UNBALANCED
OUTPUT
t
(OR XLR OUTPUT)
R
UNBALANCED
OUTPUT
t
(OR XLR OUTPUT)
• Left / Right Bass, Left / Right Treble -OR- Bass / Treble —
(0%-100%)
Use these utility menus to adjust the bass and treble
levels of the signals sent from the UNBALANCED OUT, XLR OUT,
and PHONES jacks. Select "0%" for the least amount of bass/
treble and select "100%" (default setting) for maximum bass/
treble. When the Output Configure menu (above) is set to "Mono"
you can set the bass and treble levels
independently
for the left
and right UNBALANCED OUT jacks and XLR OUT jacks. When the
Output Configure menu is set to "Stereo," only one Bass and one
Treble menu are available and both left and right channels must
be set to the same setting.
• Memory Lock —
(On/Off)
Use this menu to prevent accidental
preset modifications. You will still be able to make
temporary
changes to presets with memory lock on, but you won't be able
to save those changes until memory lock is switched off.
• Pedal Default —
(From Preset/From Pedal)
Select "From Preset" if you
want the pedal mode (volume or expression) to always be set to
the mode last stored with each preset, or select "From Pedal" if
you want to override the stored preset pedal mode and keep the
pedal in whatever mode it's currently in when you select a preset.
• Quick Access #1 / #2 / #3 —
(Preset 00-99)
Use these three utility
menus to choose Quick Access presets. You can then access those
presets quickly from the MS-4 footswitch (see MS-4 on page 6).
These menus appear only when an MS-4 is connected.
• LCD Contrast —
(0-100)
Use this menu to adjust the contrast of
the Mustang Floor display.
• MIDI In Channel —
(1-16, Omni)
Select the MIDI receiving channel.
• MIDI Out Channel —
(1-16)
Select the MIDI transmitting channel.
• MIDI Through —
(On/Off)
Turn MIDI echo on or off. Note: Sysex
packets are not echoed. If you are using the Mustang Floor
with other gear that requires Sysex, it is recommended that the
Mustang Floor is placed at the end of your MIDI chain.
• Pedal Volume CC# / Pedal Expression CC# —
(0-127)
Select the
Continuous Controller number transmitted by the pedal level in
Volume mode and in Expression mode using these utility menus.
• Pedal Switch CC# —
(0-127)
Select the Continuous Controller
number transmitted when switching the pedal between Volume
mode and Expression mode.
• EXP-1 Expression CC# —
(0-127)
Select the Continuous Controller
number transmitted by the EXP-1 pedal level. This menu appears
only when an EXP-1 is connected.
• EXP-1 Switch CC# —
(0-127)
Select the Continuous Controller
number transmitted when the EXP-1 pedal is switched on-off. This
menu appears only when an EXP-1 is connected.
• About This Amp —
This menu displays the Firmware version
currently running on the unit. Use this information to determine
if an update is available for your Mustang Floor.
Output Jacks
Output Jacks
Unbalanced Outputs
UNBALANCED OUT
R
L
The Mustang Floor provides unbalanced outputs for connection to
mono or stereo amplifiers or a combination of sound equipment.
Use the utility menus (see Utility Menus, page 7) to adjust the
mixing and voicing of the signals sent from these jacks. Use the
LEVEL knob to adjust the output level to accommodate the input
sensitivity of outboard equipment and avoid unwanted signal
distortion.
XLR Outputs
GROUND
LIFT
XLR OUT
R
L
The Mustang Floor provides XLR outputs for connection to
soundboards and recording equipment when a low signal-
to-noise ratio is required. Use the LEVEL knob to adjust the
output level to accommodate the input sensitivity of outboard
equipment. Use the utility menus (see Utility Menus, page 7)
to adjust the mixing and voicing of the signals sent from these
jacks. Press the GROUND LIFT button IN to disconnect the ground
connection which may reduce line noise in some situations.
Normally leave this button in the OUT position.
Aux / Phones Jacks
Aux / Phones Jacks
Auxiliary Input
AUX IN
You can use the Auxiliary jack to input audio into your
Mustang Floor for accompaniment. Connect the head-
phone output on your media player to the AUX IN jack
using a mini-stereo cable. Use the volume control on your player
to adjust the auxiliary volume level.
8
