background image

Fellowes warrants all parts of the binder to be free of defects in material and workmanship for 2 years from the date of purchase 
by the original consumer. If any part is found to be defective during warranty period, your sole and exclusive remedy will be repair 
or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling 
or unauthorised repair. Any implied warranty, including that of merchantability or fitness for particular purpose, is hereby limited 
in duration to the appropriate warranty period set forth above. In no event shall Fellowes be liable for any consequential damages 
attributable to this product. This warranty gives you specific legal rights. You may have other legal rights that vary from this warranty. 
The duration, terms and conditions of this warranty are valid worldwide, except where different limitations, restrictions or conditions 
may be required by local law. For more details or to obtain services under this warranty, please contact Fellowes or your dealer.

WORLDWIDE WARRANTY

Thank you for purchasing a Fellowes product. Please visit  www.fellowes.com/register to register your product and benefit from product 
news, feedback and offers. Product details can be found listed on the rating plate positioned on the rear side or underside of the 
machine.

PRODUCT REGISTRATION

Problem

Possible cause

Solution

No ‘red’ power on LED

Machine is not switched on

Switch on machine at rear next to plug 
inlet and at the wall socket

No ‘green’ ready light after a long period Machine is in a hot or humid area

Move the machine to a cooler and 
dry area

Loose and unglued sheets

Binding cover may be too thick to bind

Process the documents again, ensure 
sheets are in contact with the glued 
spine by tapping gently on a flat 
surface

Timer setting may be incorrect

Check timer setting is correct and 
process the document again

Loose and glued sheets

The cover size is too small for the number 
of sheets

Check the number of sheets is ap-
propriate for the cover width. Select 
larger spine width if necessary

Extended heating cycle

Check timer setting is correct. Ensure 
prompt document removal

Timer setting may be incorrect
Documents left on the heater plate after the 
cycle is complete

TROUBLESHOOTING

W.E.E.E.

This product is classified as Electrical and Electronic Equipment. Should the time come for you to dispose of 
this product please ensure that you do so in accordance with the European Waste of Electrical and Electronic 
Equipment (WEEE) Directive and in compliance with local laws relating to this directive.

For more information on the WEEE Directive please visit www.fellowesinternational.com/WEEE

7

Содержание Helios 60









Отзывы: