Fellowes AERAMAX PRO AM4S PC Скачать руководство пользователя страница 3

Страница: 3 / 8

AM-PRO UI & INDICATOR LAYOUT

PROJECT:

DATE:

REV:

AUTHOR:

COPERFIELD

03-AUG-16

M. GARTZ

OPERATION

The air purifier continuously works in automatic mode; the user can select which preference they would like the purifier to use based on the location or desired

operation of the air purifier. The purifier will operate through a minimized range of speeds, not exceeding the maximum level selected, in order to run quietly while

cleaning the room of contaminants. Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to reduce energy consumption and

extend the life of the filters.
When Auto Mode is selected, the Auto mode indicator will be blue. This mode uses the EnviroSmart™ technology to monitor the air quality, motion and noise level

to adjust the fan speed in order purify your air as quickly as possible. Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to

reduce energy consumption and extend the life of the filters.
When Quiet Mode is selected, the Auto Mode indicator will be purple. The machine will continue to use EnviroSmart™ but only utilizes the 3 lowest, most quiet of

the 5 fan speeds.
When Manual Mode is selected, the Manual mode indicator will be blue. This mode allows you to choose one of the 5 fan speeds and keep unit at this speed until

Auto Mode is chosen/selected. EnviroSmart™ sensors will NOT adjust the fan speed in this mode.

DISPLAY PANEL

HEPA FILTER REPLACEMENT INDICATOR

–

This indicator will show

its status when the access panel is open or closed. If the light is red this indicates

the filter needs replacing. The replacement period will vary depending on the

filters used, hours of use, air quality, and rate of air flow. For filter replacement

indicator descriptions see

FILTER REPLACEMENT INDICATORS

section.

CARBON FILTER REPLACEMENT INDICATOR

–

This indicator will

show its status when the access panel is open or closed. If the light is red this

indicates the filter needs replacing. The replacement period will vary depending

on the filters used, hours of use, air quality, and rate of air flow. For filter
replacement indicator descriptions see

FILTER REPLACEMENT INDICATORS

section.

ACCESSORY INDICATOR

–

This indicator will show its status when the

access panel is open or closed. This indicator will only be used if an accessory filter

is installed in the unit. If the light is red this indicates the filter needs replacing.

The replacement period will vary depending on the filters used, hours of use, air

quality, and rate of air flow. For filter replacement indicator descriptions see

FILTER

REPLACEMENT INDICATORS

section.

AIR QUALITY SENSOR

–

This indicator will show its status when the

access panel is open or closed. This indicator monitors the air quality and adjusts

the fan speed to keep your air purified. Blue, amber, and red lights indicate the

purity of your air.

PlasmaTRUE™ TECHNOLOGY

–

This indicator will show its status when

the access panel is open or closed. Creates an ionized field to help safely remove

airborne pollutants. To turn on and off the PlasmaTRUE™ TECHNOLOGY, touch

and hold the PLASMA indicator. A blue light illuminates when the PlasmaTRUE™

TECHNOLOGY is enabled. To disable the PlasmaTRUE™ TECHNOLOGY, press and hold

“Plasma” indicator until light is off.

AUTO MODE

–

To select, press and hold the button until the icon illuminates.

This mode uses the EnviroSmart™ technology to monitor the air quality, motion and

noise level to adjust the fan speed in order to purify your air as quickly as possible.

This button also includes QUIET MODE. To select, press and hold until the button turns

purple. The machine will continue to use EnviroSmart™ but only utilizes the 3 lowest,

most quiet of the 5 fan speeds.

MANUAL MODE

–

To select, press the button until the icon illuminates. This

mode allows you to choose one of the 5 fan speeds and keep the unit at this speed

until AUTO MODE is chosen again. The internal sensors will not adjust the fan speed

in this mode.

FAN SPEED INDICATORS

–

The fan has 5 speeds and can reach turbo

speed to clean the room in case of high levels of contaminants. The number of bars

illuminated indicates fan speed.

NOTE: after the unit is turned on the “AQ” light will flash for a few minutes while the system self-calibrates.

1 – whisper
2 – low
3 – medium

4 – high
5 – turbo

CARE AND MAINTENANCE

CLEANING:

• Clean external housing as necessary by wiping with a dry, soft cloth; for stains, use a warm, damp cloth.

• Do not use volatile fluids such as benzene, paint thinner, scouring powder or other cleaners that may damage the unit surface.

• Clean intake and exhaust vents by wiping with a dry, soft cloth.

Unlock access panel: to unlock, insert

the key provided and rotate counter-

clockwise ¼ turn.

Touch and hold the illuminated

indicator for three seconds

until a beep is heard and the

indicator is flashing green.

Open front access panel by pressing

latches on both sides of unit. Allow

panel to open fully. Remove filter(s)

to be replaced.

Release finger from indicator.

Remove any packaging wrap from the

new filters(s) and re-install the filters.

Touch and hold the indicator for

three seconds until a beep is heard

and the indicator light turns off.

FILTER REPLACEMENT INDICATORS:

The replacement filter indicators will signal when to replace the HEPA Filter and/or Carbon with Pre-Filter. The replacement period will vary depending on the hours of use, air

quality, and rate of air flow. However, under normal usage, most HEPA Filters need to be replaced every 2 years, and Carbon with Pre-Filter every 6 months. When a filter needs to

be replaced the following color will be shown on any one of the HEPA, CARBON, or ACCESSORY filter replacement indicators:

Red Flashing = RIGHT filter 90% full

Amber Flashing = LEFT filter 90% full

Red Flash, Pause, Amber Flash, Pause = Right & LEFT filters 90% full

Red = Replace RIGHT filter

Amber = Replace LEFT filter

Red & Amber Alternating = Replace Right & Left filters

Do not wash and reuse any of the filters – they will not work effectively. Only use AeraMax® PRO brand replacement filters as units will not function using any other

replacements.

FILTER REPLACEMENT PROCEDURE:

FILTER REPLACEMENT:

When installing a new filter the unit will automatically detect the filter type but the user will have to manually reset the filter replacement indicators. To reset the flashing filter
replacement indicator use the following procedure:

TROUBLESHOOTING

PROBLEM:

POSSIBLE SOLUTION:

The air quality control system fails to start.

• Check to assure unit is connected to power supply.
• Make sure filters are genuine AeraMax

PRO filters, as unit will not function with other

brands. IMPORTANT: Make sure filter detection area on genuine AeraMax

PRO

  replacement filter aligns with window in filter frame.
•  Review “Re-Installing Filters” section for further detail.
•  Make sure front access panel is closed completely.
•  Make sure power switch is on.

The unit makes a faint ticking sound.

•

This indicates that the “PlasmaTRUE™” bipolar ionizer is working.

The HEPA and/or Carbon Filter replacement indicator light

remain lit after replacing the filter(s).

• Repeat filter light reset instruction.

Note: If you do not complete step three within 10 seconds of completing step 1 then the indicator light will not be reset.