Federal Signal Corporation WV450XL Series Скачать руководство пользователя | Manualshive

Страница: 9 / 24

background image

9

Installation and Maintenance Instructions

Model WV450XL Series

Figure 2 Mounting hole locations Ex de version

290A7613

Ex de VERSION

ø8.9 [ø0.35] X 3

MOUNTING HOLES

97.1 [3.82]

57.4 [2.26]

M20 GLAND ENTRIES

3 POSITIONS

CERTIFICATION LABEL

WARNING LABEL

EExde COVER SCREWS

See Figures 1 and 2. The Federal Signal WV450XL Series LED

beacon is mounted using a mounting bracket fixed to the base of

the unit. Install the enclosure on the selected support surface using

the three 9.0 mm (0.35 in) mounting holes. Use installer-supplied

fasteners suitable for the surface to which the device will be mounted.

Safety Messages for Wiring

When installing and operating explosion-proof electrical equipment,

the relevant national regulations for installation and operation (e.g.,

EN60079-14 and IEC Wiring Regulations) must be observed.
• To maintain the explosion-proof integrity of the enclosure,

DO NOT damage the dome or threads while disassembling or

reassembling unit.

• Painting and surface finishes, other than those applied by Federal

Signal Corporation are not permitted.

• Cable termination should be in accordance with specifications

applying to the application. Federal Signal recommends that all

cables and cores should be fully identified.

• Ensure that only the correct component certified glands are used

and that the assembly is shrouded and correctly earthed. Gland

entries are M20-1.5 6H. Supply wires to be rated 85 °C minimum.

«
...
7
8
9
10
11
...
»

Содержание WV450XL Series

























Отзывы:

Нет отзывов

Похожие инструкции для WV450XL Series

Бренд: GE Страницы: 36

Security Camera

Бренд: Raritan Страницы: 2

Бренд: Data Harvest Страницы: 19

Security Camera

Бренд: TANDBERG Страницы: 247

JBL BAR 5.1 SURROUND

Бренд: Harman Страницы: 4

Бренд: Harman Страницы: 48

Infinity KAPPA 4100msb

Бренд: Harman Страницы: 8

JBL PARTYBOX ON-THE-GO

Бренд: Harman Страницы: 17

JBL CINEMA SB190

Бренд: Harman Страницы: 19

Бренд: K-array Страницы: 20

MIG 208 Alu Synergy

Бренд: Magnum Страницы: 24

Бренд: Varian Страницы: 55

Бренд: Xiaomi Страницы: 36

Бренд: Hanwha Vision Страницы: 20

Бренд: CP Electronics Страницы: 12

NAC-HD-329VL/60

Бренд: Navaio Страницы: 2

Бренд: Basalte Страницы: 2

MMA-300/2 PROFI

Бренд: Zenit Powertools Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды