Federal Signal Corporation Valor Low-Profile Hook Скачать руководство пользователя

Страница: 2 / 8

Valor

Low-Profile Hook Mount Manual

Valor Low-Profile Hook Mount Kit

Federal Signal

www.fedsig.com

Table 1 Kit contents

Qty.

Description

Second Item No.

Screw, #10, Type B, Pan-Head Torx

, Steel

7011246-08

Nut, 5/16-18, High-Corrosion Resistant

7059125

Nut, Flange 5/16-18, High-Corrosion Resistant

7065078

Washer, Flat, Stainless Steel, 0.344 x 3/4 x 0.050 inch

7072A031

Lockwasher, Split 5/16 inch Screw, Stainless Steel.

7074A020

Retainer, Nut, Arjent/Vista

8583490

Foot, Low, LH, Valor, (Left)

865101872

Foot, Low, RH, Valor, (Right)

865101873

Bracket, Low, Hook Attach, LH, Valor (Left)

865101874

Bracket, Low, Hook Attach, RH, Valor (Right)

865101875

The items above are factory-installed on new light bars.

Qty.

Description

Second Item No.

Screw, Machine, 5/16-18, Torx. Steel

7000434-14

Screw #10, Type B, Pan-Head, Torx, Steel

7011246-08

Washer, Flat, Stainless Steel, 0.344 inch, .0.563 inch outer diameter

7072234

Lockwasher, Split, 5/16 inch

7074A020-01

Mounting Pad

8572029

Valor Low Hook Adjuster Assembly

865101876

Keeper Plate Kit

8583193

Installing the Service Kit Mounting Feet

HEAVY OBJECT: Use lifting aids and proper lifting techniques when removing or replacing the

light bar. Failure to follow this warning may cause personal injury.

HOOK ATTACH BRACKET RETAINER NUTS: Torque the two 5/16 in nuts that retain the hook-

attach bracket to the mounting foot to 16-24 in-lb only. See Figure 2 on page 4.

PROPER MOUNTING FEET INSTALLATION: Before installing the mounting feet and hook-attach

bracket, note that the LH foot and bracket are for the left side of the light bar, and the RH foot

and bracket are for the right side. Failure to note this difference may damage the light bar.

The service kit requires the assembly of the mounting feet on the light bar. If you are installing a new

light bar that is shipped with the mounting feet already assembled, see "Installing the Adjustable Foot

Brackets" on page 4. New light bars may require that you loosen the 5/16-inch nuts to adjust the

positions of the mounting feet on the vehicle roof. Before installing the light bar, plan all cable routing.
To install the mounting feet:

Содержание Valor Low-Profile Hook









Результаты поиска

Содержание Valor Low-Profile Hook

Отзывы:

Похожие инструкции для Valor Low-Profile Hook

Бренды по названию

Популярные бренды

Federal Signal Corporation Valor Low-Profile Hook, Руководство пользователя

Результаты поиска

Содержание Valor Low-Profile Hook

Отзывы:

Похожие инструкции для Valor Low-Profile Hook

Бренды по названию

Популярные бренды