Federal Signal Corporation UltraVoice UVRI-B Series Скачать руководство пользователя страница 53

Страница: 53 / 56

Troubleshooting

Description, Specifications, Installation, and Operation Manual

Federal Signal

www.fedsig.com

4. Remove the battery bracket and then remove the battery.
5. Reassemble in the reverse order of these steps.

Troubleshooting

Table 32 Troubleshooting

Problem

Action

No Radio Decode

• Unit is not programmed to recognize that particular code

sequence or signal is not being received properly.

• Verify programming is correct. Check the received audio signal

quality at the RX test pin on the front of the control

card

Low output from

speaker array

Check battery voltage. Also check signal indicators on amplifiers

during a function. If indicators are off, remove amplifier for service.

Function stops

before normal

timeout

Batteries may require further charging. Check battery voltage under

load. Check charger output.

Local PA feeds back Lower PA volume using knob above MIC connector.
Local PA has little or

no output

Hold microphone close to mouth. Increase PA volume using knob

above MIC connector

Batteries not holding

charge

Check that the battery fuse is intact and check charger output.

Load test batteries.

Relay outputs do not

operate

With a voltmeter, check that there is at least 12 Vdc across TP16

and TP18.

Radio PA takes too

long to timeout

Check radio for proper operation of squelch.

CD LED should light while carrier is present

Replacement Parts

The UVRI-B has the following replacement parts.

Table 33 Replacement Part Numbers

Description

Part Number

Control Board

Q20000253

Amplifier Board, 100 W

Q20000324

148142A, 20 Ampere auto fuse

Littlefuse

287020

Bussman # GDC-5A

148186-02, 5 Ampere fuse

Battery, 12V, 12 Ah

Q155193A

Radio

19901665-XX

Microphone

MNC-MC

Ambient noise level monitoring Microphone X-SM1-FS1
UVRI-B Power Cable, 24 Vdc

Q17501999A

Service Part Fuse 2 per unit

Bussman part – GDC-5A

Littlefuse part p 218005.HXP

Not Available through Federal Signal

Содержание UltraVoice UVRI-B Series

























































Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы:

Federal Signal Corporation UltraVoice UVRI-B Series, Описание, характеристики, установка и руководство по эксплуатации, Страница: 53 / 56

Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы: