manualshive.com logo in svg
background image

Installation and Programming Instructions

2

SignalMaster

 Model 330104 SMC1 Light Bar Controller 

Federal Signal 

www.fedsig.com

Table 1 Halogen SignalMaster

 directional warning lights  

(for CAC Title 13, Article 22 compliance)

Model

Length

Lamps

Cable

Lenses

320142

20 in

4

30 ft

Amber

320162

31 in

6

15 ft

Amber

320612

31 in

6

30 ft

Amber

320172

42 in

8

15 ft

Amber

320182

42 in

8

30 ft

Amber

320192

42 in

8

50 ft

Amber

320602

84 in

8+ DOT Strip

35 ft

Amber

Table 2 VPX SignalMaster directional warning lights 

(for CAC Title 13, Article 22 compliance)

Model

Length

Lamps

Cable

LEDs

Lenses 

320900

20 in

4

30 ft

Amber

Amber

320905

31 in

6

15 ft

Amber

Amber

320910

31 in

6

30 ft

Amber

Amber

320915

31 in

6

60 ft

Amber

Amber

320920

42 in

8

15 ft

Amber

Amber

320925

42 in

8

30 ft

Amber

Amber

320930

42 in

8

60 ft

Amber

Amber

320935

51 in

8

30 ft

Amber

Amber

320940

51 in

8

50 ft

Amber

Amber

The WARN function provides a non-directional flash pattern for use when a directional signal may not be 

appropriate. One pattern can be selected from the ten patterns available, which include seven standard 

patterns and three patterns that are compliant with CAC Title 13, Article 22. Some patterns are optimized 

for LED products and flash too quickly for a halogen light bar. The default pattern is the classic SMC warn 

pattern with four center light heads alternating with the two light heads on each end. 
When standard directional signal operation is selected, the lamps illuminate sequentially in a sweeping 

motion until all are illuminated, and then the pattern repeats. When Title 13 Mode is selected, the lamps 

are extinguished more quickly than in standard mode. Title 13 Mode provides patterns that comply with 

the 40 percent to 60 percent on-time and flash rate of 60 FPM to 120 FPM, which are requirements of 

CAC Title 13, Article 22.
Although the controller operates at 12 Vdc to 24 Vdc, ensure that the SignalMaster light bar is of the 

proper voltage for the electrical system of the vehicle. Do not operate a 12 V SignalMaster at 24 V or a 

24 V SignalMaster at 12 V, or shortened lamp life will result. 

Содержание SignalMaster 330104 SMC1













Отзывы: