Fayat Group 897 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 590

Fayat Group 897 Скачать руководство пользователя страница 94

D 13 2

Danger due to improper operation

Improper operation of the vehicles can cause severe
to fatal injuries!

- The vehicle may only be used in the proper manner for its

intended purpose.

- The vehicle may only be operated by trained staff.
- The vehicle operators must have made themselves famil-

iar with the contents of the operating instructions.

- Avoid jerky movements of the vehicle.
- Do not exceed the permissible angle of rise and slope.
- Keep hoods and covering parts closed during operation.
- Comply with all further information in these instructions

and in the safety manual.

Danger of being pulled in by rotating or conveying
vehicle parts

Rotating or conveying vehicle parts can cause severe
or fatal injuries!

- Do not enter the danger zone.
- Do not reach into rotating or conveying parts.
- Only wear close-fitting clothing.
- Comply with the warning and information signs on the vehicle.
- Stop the engine and remove the ignition key for any main-

tenance work.

- Comply with all further information in these instructions and

in the safety manual.

Danger of crushing due to moving vehicle parts

Vehicle parts performing movements can cause severe
or fatal injuries!

- Remaining in the vehicle's danger zone during operation

is prohibited!

- Do not reach into the danger zone.
- Comply with the warning and information signs on the vehicle.
- Comply with all further information in these instructions and

in the safety manual.

DANGER

WARNING

WARNING

«
...
92
93
94
95
96
...
»

Содержание 897















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов