Fayat Group 897 Скачать руководство пользователя страница 315

Страница: 315 / 590

D 43 9

- If necessary, start the engine of the vehicle supplying power and leave to run

for a while.

Now try to start the other vehicle:

- Press the starter button (12) to start the engine. Run the starter continuously for a

maximum of 30 seconds, then take a break for 2 minutes!

- If the engine still has not started after two attempts, ascertain the cause!

- If the engine starts up: disconnect the starting aid cable again in reverse order.

Содержание 897















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 897

Отзывы:

Fayat Group 897, Руководство по эксплуатации и техническому обслуживанию, Страница: 315 / 590

Результаты поиска

Содержание 897

Отзывы: