Fayat Group 897 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 590

Fayat Group 897 Скачать руководство пользователя страница 115

D 13 23

A

The Truck Assist system is used for communication between the driver of the paver
and the driver of the material truck. The corresponding signal system shows the truck
driver which action to perform (reversing / stop / tip material / depart).

Caution! Possible material damage through insuffi-
cient instruction

Ignored or incorrectly understood signals can cause dam-
age to the paver and/or material truck!

- The paver driver and all drivers of the material trucks

must be instructed in how the Truck Assist system works
and understand the system.

- Comply with all further information in the operating

instructions and in the safety manual.

Pos. Designation

Brief description

LED display

38

Tell truck
to reverse

Pushbutton function with LED feedback:

- To change over to the "Start Revers-

ing" signal. (GREEN SIGNAL)

- Press button again to change signal

over to "Stop".
Button LED (39) on + (RED SIGNAL).

- Press button once more to switch

again to "Start Reversing" signal.
(GREEN SIGNAL)

A

Button (39) can also be used to change
over to "Stop".

39

Tell truck
to interrupt
reversing - "STOP"

Pushbutton function with LED feedback:

- To change over to the "STOP" signal.

(RED SIGNAL)

A

Set "STOP" signal to interrupt procedure
or on reaching correct distance between
truck and paver.

NOTE

«
...
113
114
115
116
117
...
»

Содержание 897















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов