Favor.it RS10 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 23

background image

523323 PUBLICATION DATE 2 OCT 2006.DOC

INSTALLATION AND MAINTENANCE MANUAL

17

•

If it is not possible to install the belt on the tension pulley, we can move the motor (16). Loosen the bolt M8 (11)

which ensures the correct position of the motor. Move the motor to enable the belt installation and fasten it.
Tighten the securing bolt (11) carefully so that it would not deform the plastic washers (14,15).

•

Put a new belt PJ1473 (2) on the pulley. Installation of the belt is done in reverse order compared to its removal.

Take care so that the tension springs (7) would be fasten to openings in the pulley support and to the frame
hinge.

•

The belt must be placed in the correct grooves of the tension pulley, so that it could move in the middle of

the drum pulley width.

•

Testing force of the correctly tight belt between the drum pulley and tension pulley is 100 - 110Hz, (180 - 210N),

measured by tension meter for measuring the force in the belt.

•

Testing force of the correctly tight belt between the tension pulley and motor is 175 - 205Hz, (200 - 270N),

measured by tension meter for measuring the force in the belt.

•

If the belt tension does not correspond to determined values, we can adjust the belt tension by means of the bolt

which holds the springs or by additional moving the motor.

1. Drum pulley
2. Belt PJ1473
3. Pulley complete
4. Securing ring
5. Bolt M6x6
6. Belt PJ559
7. Spring
8. Bolt with eye M8x50
9. Nut M8
10. Pin
11. Bolt 5/16“x11/4“
12. Spring washer 8
13. Washer 8
14. Plastic washer 8,4x25x2
15. Plastic washer 8,2x12x3
16. Motor

Fig. 5.8.A. Flat belt, valid for 10 kg / 25 lbs

REPLACEMENT OF THE BELTS FOR THE MACHINE WITH CAPACITY
18 kg / 40 lbs, 22 kg / 50 lbs

1. Drum V-pulley
2. Belt PJ1956
3. Motor
4. Motor V-pulley
5. Motor board
6. Spring

Fig. 5.8.B. Flat belt, applicable for 18 kg / 40 lb,
22 kg / 50 lb

«
...
16
17
18
19
20
...
»

Содержание RS10
























Отзывы:

Нет отзывов

Похожие инструкции для RS10

Бренд: Kärcher Страницы: 62

Бренд: Maidaid Halcyon Страницы: 17

Бренд: Wap Страницы: 20

Бренд: Hoover Страницы: 104

Бренд: Alliance Laundry Systems Страницы: 48

CLW-108i and CLW-128i Installation / Operation / Maintenance M

Бренд: Cole Parmer Страницы: 50

Бренд: Summit Страницы: 1

Бренд: Euromaid Страницы: 33

Бренд: Merax Страницы: 22

Бренд: GE Страницы: 28

Бренд: GE Страницы: 20

Бренд: CleanCraft Страницы: 88

Бренд: Logik Страницы: 108

Бренд: Hoover Страницы: 17

EVA-VX 5.5; Elena Aqua SX 6.0

Бренд: IFB Страницы: 25

Бренд: Alto Страницы: 35

KUD-WC1113KUD-WD1117

Бренд: Unique Klasse Страницы: 54

Бренд: Mestra Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды