background image

Heat recovery unit with cooling circuit - 

RCF

 -

0208-6180549-rev. 02

5

GB

Controls manual 

Introduction

The control installed on the RCF 

units is a compact device usually 

provided  to control air conditio-

ning units. 

   Carefully  and  thoroughly  read  all  the 

information referred to in this manual. Pay 
particular attention to the norms accompanied 
by the indication “DANGER” or “ATTENTION” 
since, if not observed, may cause damage to 
the unit or to people. 

•   If any malfunctions are found out, which are 

not included in this manual, please  contact 
the local After-Sales Service immediately.

•  

FAST S.p.A. declines all liability for any 
damage caused by the improper use of the 
machine or the partial or superficial reading of 
the information contained in this manual.

•   Installation  and  maintenance  must 

be  performed  by  qualified  and 
experienced  personnel,  having  the 
requirements  that  are  foreseen  by 
law  46/90  and/or  the  DL  380/2001 
for  the  electrical/electronic  and 
air-conditioning  installation,  with 
consequent  registration  at  the  local 
CHAMBER  OF  COMMERCE,  if  this  is 
not  so,  FAST  S.p.A.  declines  all 
responsibility  regarding  the  safety  of 
the product.

THE  MANUFACTURER  DECLINES  ALL 
LIABILITY  FOR  DAMAGE TO THINGS  OR 
INJURY  TO  PERSONS  AND  ANIMALS 
CAUSED  BY  THE  FAILURE  TO  OBSERVE 
THE INSTRUCTIONS AND STANDARDS IN 
THIS MANUAL.

Although suitable risk analysis have been 
performed during the design of the RCF 
unit,  PAY  ATTENTION  to  the  pictograms 
on  the  machine  which  help  understand 
the  manual  better,  rapidly  catching  the 
attention of the reader concerning the risks 
which can not be avoided or sufficiently 
limited  through  the  use  of  technical 
protection means and measures.
G E N E R A L   H A Z A R D   S I G N A L

Carefully  adhere  to  all  the  indications 

n e x t  

t o  

t h e  

i c o n . 

Failure  to  comply  with  the 
instructions may generate hazardous 

situations  with  possible  damage  to  the 
health of the operator and user in general.

DANGEROUS  ELECTRICAL  VOLTAGE 
SIGNAL 

Carefully adhere to all the indications 
next to the icon. 
The signal indicates components of 

the unit or, in this manual, specifies actions that 
could generate electrically-related risks.

GENERAL PROHIBITION SIGNAL

Carefully  adhere to all the indications next to the 
icon that limit actions in order to guarantee better 

operator safety.

MAIN WARRANTY

CONDITIONS

•   The warranty does not cover payment for 

damages cause by the incorrect installation of 
the unit by the installer.

•   The warranty does not cover payment for 

damages cause by the improper use of the 
unit by the user. 

•   The manufacturer is not responsible for 

accidents to the installer or user that are due 
to the improper use and incorrect installation 
of the unit.

The warranty is not valid when:

•   the maintenance and repairs have been 

performed by unauthorised persons or 
companies;

•   the unit has been previously repaired or 

modified with spare parts that are not original; 

•   the unit has not undergone suitable 

maintenance;

•   the instructions described in the present 

manual have not been followed correctly;

•  unauthorised modifications have been made.

Note:
The  Manufacturer  reserves  the  right  at 
all  times  to  make  any  modification 

for  the  improvement  of  its  product 
and  is  not  obliged  to  add  these 
modification  to  machines  of  previous 
manufacture,  which  have  already 
been  delivered  or  are  being  built.
The warranty conditions are any subject 
to  the  general  sales  conditions  at 
the  moment  the  contract  is  finalised.

Содержание RCF Series




























Отзывы: