Faroudja Faroudja DVP1080MF, Инструкция по установке и эксплуатации

Страница: 10 / 22

10
SetuP Menu
OVERVIEW: The SETUP Menu offers many
selections to optimise the processor for
installation. Be sure to completely review the
menu items and application notes to insure
proper operation.
PRESS THE MENU KEY ON THE REMOTE
FOR 7 SECONDS TO ENTER SETUP MENU
SETUP Menu functions are visible on the front
panel, not on the On-Screen-Display. Use the
directional buttons on the remote to navigate.
Defaults are shown in
Bold
below.
SET: NTSC SCAN RATE
This sets the output rate when a 60Hz source
is auto-detected.
• Press STORE TWICE (2X) to enter the new scan
rate. Store different output rates as Profiles. See
Storing Profiles on pages 11/12.
• Be sure to review the display device manual to
determine which output rate to choose.
SET: PAL SCAN RATE
This sets the output rate when a 50Hz source
is auto-detected.
• Press STORE TWICE (2X) to enter the new scan
rate. Store different output rates as Profiles. See
Storing Profiles on pages 11/12.
• Many digital displays have limited support of
50Hz signals. Be sure to check with the display
device’s manual to determine the proper output
rate.
SET: SCREEN SHAPE
WIDESCREEN
/ WIDE-4:3 / 4:3
Set Screen shape to match the aspect ratio of
the display device.
• Select Wide-4:3 (4:3 Letterbox) when using a
4:3 native projector on a 16:9 screen.
• When using a 4:3 projector and anamorphic
lens on a 16:9 screen, select Widescreen.
• Screen shape defaults to AUTO when in HIGH
BANDWIDTH mode
SET: ANALOGUE BLACK LEVEL
0 / 7.5IRE
Sets correct black level for YPrPb DVD sources.
• Many DVD players offer black level options
(sometimes called “Enhanced Blacks”). The
player should be left at default settings:
adjust level in the DVP1080MF
.
• Only available when the Component input is
selected with a 60Hz source.
SET: HD INPUT H-ADJUST
0-50 ( 25 Default )
Adjusts the horizontal position of High
Definition sources (720p/1080i) to match the
horizontal position from Standard Definition
sources.
• First align the proper image size and position on
the display using a test pattern from a DVD. Use
the H/V, L/R and sizing controls in the display
device, if available. Use the H/V adjustments in
the DVP1080MF OSD if the display does not
offer them. Then switch to the HD source and
adjust the HD INPUT H-ADJUST to match.
• Available only when a 1080i/720p signal is
detected. Not available in HIGH BANDWIDTH
mode
» The input for the HD source must be selected in
order to make the HD H-ADJUSTMENT.
» Some display devices offer minimal image
adjustments when using the DVI inputs.
» Some HD satellite receivers offer H-adjustments.
Those can also be used in conjunction with this
function to get the best results.
SET:DVI INPUT LEVEL
DVI-VIDEO(16-235)
/ DVI-PC(0-255)
Sets the correct input signal level to match the
DVI input source.
• 0-255 is typical for digital display devices
inputs (the processor output is 0-255), 16-235
is typical for video sources. However, not all
sources follow the rules. If the processor DVI
input level is set to 0-255 but the source is 16-
235, the image will lack dynamic range.
• To test what the output is from the source,
put up a 10 step gray scale pattern from a test
pattern DVD. 16-235 and 0-255. The correct
setting is when all 10 bars are visible and evenly
lit. An incorrect setting will produce an image
that either looks dull or the brightest and
darkest bars are missing (clipping).
0-255 16-235 Setting = Image too bright
16-235 0-255 Setting = Dull Image
• Only available when DVI input is selected
INPUT ENABLE / DISABLE
Each input can be enabled or disabled
depending on the installation. Deactivating