Faro FaroArm Fusion Скачать руководство пользователя

Страница: 39 / 130

FaroArm

Manual

January 2009

Chapter 1: Introduction to the FaroArm

LEDs

The two LEDs, on the back of the Laser Line
Probe, indicate the distance to the target object
from the Laser Line Probe. Remember, data is
only sent to the computer when the Laser Line
Probe is in range.

• Out of Range (two Red LEDs). The Laser Line

Probe is too close or too far from the part.

• Center Range (two Green LEDs) The Laser

Line Probe is in the center of the range.

• Near Range (top Green LED only) The Laser

Line Probe is in range, closer to the part.

• Far Range (bottom Green LED only) The

Laser Line Probe is in range, farther from the
part.

Additionally, the software uses the R

ANGE

INDER

dialog box to show the distance and

position from the Laser Line Probe to your part.

Range Finder

The FARO Laser Line Probe software has a R

ANGE

INDER

dialog box.

This dialog box graphically displays the laser to part distance and the
area of the laser line that the camera is processing.

When the Laser Line Probe is within the operating range, the center of
the target displays as a small box in the R

ANGE

INDER

dialog box, see

Figure 1-29.

The box moves as the Laser Line Probe moves:
• Up - as you move the Laser Line Probe closer to your part

Figure 1-29 Laser Line Probe in range

Figure 1-30 Laser Line Probe not in range

08M46E00_FaroArmUSB.book Page 31 Tuesday, February 17, 2009 1:42 PM

Содержание FaroArm Fusion



































































































































Результаты поиска

Содержание FaroArm Fusion

Отзывы:

Похожие инструкции для FaroArm Fusion

Бренды по названию

Популярные бренды

Faro FaroArm Fusion, Руководство пользователя

Результаты поиска

Содержание FaroArm Fusion

Отзывы:

Похожие инструкции для FaroArm Fusion

Бренды по названию

Популярные бренды