FarmTek Growers Supply GrowSpan Gothic Pro 113836R Скачать руководство пользователя

Страница: 21 / 59

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.06.18 113836_37_38_39R

END PANEL INSTALLATION (continued)

NOTE:

Space FA4484B Tek screws evenly at 16"

on-center when securing panels. DO NOT USE

WASHERS WHEN SECURING H-CHANNEL TO END

FRAME.

DO NOT install profile on bottom of end wall panels.

These edges are sealed with vent tape.

Use an FA4484B Tek screw and washer to secure panel to

end wall frame. Do not crush panel when installing screws.

GLAZING PANEL

8MM POLYCARBONATE

PANEL SPLICE "H" CHANNEL

TEK SCREW

END WALL FRAME TUBE

TEK SCREW & NEO-BONDED WASHER

Diagram shows basic panel installation and fasteners used

to secure polycarbonte panels.

In photo below, top of panel is removed using a power

tool equipped with a round cutting bit. Use rafter as a

guide for best results.

NOTE:

Actual greenhouse frame may differ.

4. Continue installing panels and aluminum profile in the

locations shown on the end panel diagrams (Quick

Start section) for the front and back end walls.

U-channel profile (104213) is also installed along panel

bottoms

above doors

to finish those edges.

5. Continue installing the polycarbonate panels as

described for the front and back end walls.

ATTENTION:

U-channel profile is installed along the

edges of the panels shown in the diagram below.

Cut upper panel

to proper length.

Frame shown above may differ from actual frame.

6. Continue with the

Double Door Assembly

procedures.

Install profile here.

Содержание Growers Supply GrowSpan Gothic Pro 113836R




























































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 113836R

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 113836R

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Pro 113836R, Руководство пользователя

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 113836R

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 113836R

Бренды по названию

Популярные бренды