FarmTek Growers Supply GrowSpan Gothic Pro 113836R Скачать руководство пользователя страница 38

Страница: 38 / 59

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

113836_37_38_39R Revision date: 06.06.18

3. Take the aluminum channel and drill a 3/8" hole through

the channel 2" from one end and attach a threaded rod

using a 3/8" nut on each side of the channel.

TWIST-OF-THE-WRIST ASSEMBLY (continued)

4. With lower end of channel approximately 4" above the

ground, position channel along rafter at the end where

the Twist-of-the-Wrist assembly will be located.

5. Secure upper end of channel by drilling a 3/8" hole

through end rafter. Attach as shown. Lower end of

channel will "float" and is not attached.

NOTE:

Install a flat washer between nut and end wall

polycarbonate panel.

6. Select bearing bracket and attach bearings. (In some

instances, bearings may come already attached.)

Assemble bearings as follows if shipped unassembled:

NOTE

: Attach single bearings to sides of bracket and

double bearings to middle portion of bracket. Use

1/4" hex bolts and locknuts as needed. Install a flat

washer on both sides of each bearing to insure proper

operation of bearings and the assembly.

7. Install longer bolts with bearings on the side of the

bracket that has two holes. Install these

before

installing the double bearing assembles. See figures

below.

8. For spacers on long bolts, insert a 5/16" nut over each

bolt.

These nuts are used as spacers only.

5/16" Nut

9. Slide the Twist-of-the-Wrist mounting plate over the

long bolts and secure plate using two locknuts.

Locknuts

10. Attach Twist-of-the-Wrist gearbox to the mounting plate

using hex head bolts included with plate.

Top View

Содержание Growers Supply GrowSpan Gothic Pro 113836R




























































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 113836R

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 113836R

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Pro 113836R, Руководство пользователя

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 113836R

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 113836R

Бренды по названию

Популярные бренды