FARMSCAN Jackal v2 Скачать руководство пользователя страница 37

Страница: 37 / 48

September 2015

www.farmscanag.com

AM-JACKAL-3

Air/Volt/Depth/%/Temp Pressure Sensor

CALIBRATION (LIVE READOUT)

The Jackal also allows for a semi-automatic setup when the voltage values are unknown for a particular voltage
input. A live voltage readout is displayed in the top left hand side when the sensor is active.

Follow the previous 5 steps followed by :

Press

EDIT

to change the

unit. kPa,psi,bar,Volt,%,

i.e. kPa

Engage the implement

and/or adjust the pressure

manually to the low point the

sensor will need to operate

in.

The voltage will now be

displayed. e.g.

1.75v

In the above example we can

set the minimum of

1kPa

HIGHLIGHTING

EDITTING

the values as required.

Press

SET

. This will copy the

live voltage into the

CAL LOW

voltage point

Repeat the previous 2 steps

for the

CAL HIGH

values

Highlight or confirm the UOD

(Unit of Display)

e.g. kPa

Press

NEXT

when done

You have the option to set

Alarm Min/Max points if
required. Using the NAV
buttons select & EDIT as

required. Press NEXT

Name the input if you desire,

Press EDIT

or Press NEXT

The Wizard is now complete.

Press NEXT

You will be returned to the

Setup Screen.

Press EXIT

Example: 1UP Display of

kPa

THIS ENDS THE SETUP FOR A VARAIBLE VOLTAGE INPUT SENSOR

Содержание Jackal v2

















































Результаты поиска

Содержание Jackal v2

Отзывы:

Бренды по названию

Популярные бренды

FARMSCAN Jackal v2, Общее описание устройства

Результаты поиска

Содержание Jackal v2

Отзывы:

Бренды по названию

Популярные бренды