FARMSCAN Jackal v2 Скачать руководство пользователя страница 34

Страница: 34 / 48

September 2015

www.farmscanag.com

AM-JACKAL-3

Bin Level Sensor

BIN LEVEL SENSOR

The Jackal can be configured with a bin level sensor for detecting empty/full

Sensors Required:

Bin Level Sensor (A-2220P/2060)

Any other style (High/low) or (On/Off) or (Empty/Full)

Available Connections (

PAGE 4

)

This setup section assumes that physical wiring for the required sensors have been
completed. If not please refer to

PAGE 8

on wiring requirements

SETUP

From the front screen press

SETUP

Highlight

WIZARD

& press

SELECT

Highlight

GENERIC WIZARD

press

SELECT

Highlight the

INPUT

number

(9-13)

to where the sensor

wire is connected into on the

rear of the Jackal & press

NEXT

Enable the input by pressing

EDIT

Press

EDIT

to change the

unit. Full/Empty, H/L

(high/low), On/Off

State will

updated “Live” For

example. Low = bin empty,

High = bin full. Test by placing

hand around sensor.

Highlight Level & select

LEVEL.

This can be changed

from Normal to Invert. (Can

be used if Full/empty is

reversed) Press

NEXT

Highlight the Unit of Display

that you wish to be displayed

on the front screen.

Press

NEXT

You have the option to set

Alarm Min/Max points if
required. Using the NAV
buttons select & EDIT as

required.

Press NEXT

Name the input if you desire,

i.e. BIN1.

Press EDIT

or Press NEXT.

Wizard is now complete.

Press NEXT

Press EXIT to return to the

front screen

THIS ENDS THE SETUP FOR A BIN LEVEL SENSOR

Содержание Jackal v2

















































Результаты поиска

Содержание Jackal v2

Отзывы:

Бренды по названию

Популярные бренды

FARMSCAN Jackal v2, Общее описание устройства

Результаты поиска

Содержание Jackal v2

Отзывы:

Бренды по названию

Популярные бренды