manualshive.com logo in svg

FARMSCAN Jackal v2, Общее описание устройства

Поделиться
Скачать
FARMSCAN Jackal v2 Скачать руководство пользователя страница 12

 

September 2015 

www.farmscanag.com 

AM-JACKAL-3 

11 

Overview 

OVERVIEW 

 

BUTTON FUNCTIONS 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

 

Power On/Off button 

a.

 

Power is turned on  by  a short press of  the 

ON/OFF

 Button (1  second).  

b.

 

Power is turned off  by  two (2) short presses. 

2.

 

Run/Hold button 

a.

 

The 

RUN/HOLD

 button has a dual function.  

a.

 

Press 

RUN/HOLD

 

once to place the ‘MONITOR ON HOLD’. 

 

b.

 

Press 

RUN/HOLD

 again to resume operation. 

b.

 

The 

RUN/HOLD

 state is indicated in the top left hand corner of the screen. When the monitor is in 

RUN mode, the unit displays RUN to signify that the monitor is active.  

c.

 

When the monitor is in 

HOLD

 mode the unit displays the word 

“

HOLD

”

 

3.

 

Menu/Page button 

a.

 

The 

MENU/PAGE

 button is used for setting up the ports as well as returning to the main screen from  

TRIPS

 or 

TOTAL

 displays 

4.

 

Select button (3 off) 

a.

 

The Jackal has 3 soft buttons placed directly under the LCD. These buttons will change function in 
different menus.  

b.

 

The function of the soft button is indicated at the bottom of the screen directly above the button.  

5.

 

Navigation button (Up, Down, Left, Right, Enter) 

a.

 

The Round navigation (

NAV

) buttons are used to navigate 

UP/DOWN

/

LEFT/RIGHT

 in calibration screens. 

b.

 

ENTER 

is used to select the option highlighted onscreen.  

 

4 

3 

 

1 

 

2 

5 

Содержание Jackal v2

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды