Farmi Forest Corporation VALBY CH 260 Скачать руководство пользователя страница 7

Страница: 7 / 48

SAFETY INSTRUCTIONS

CH 260 CHIPPER

www.farmiforest.fi

--- 7 ---

3.3.SAFETY INSTRUCTIONS FOR THE HYDRAULIC UNIT

Before performing lubrication work on any equipment, consult the manufac-

turer’s instruction manual and follow the recommended procedures.

Before lubricating the machine, shut down the engine and stop the ma-

chine.

Pressurized oil can be hazardous. Pressurized oil jet can penetrate skin and

cause serious injuries or death.

Occasional skin exposure with oil is not dangerous. If though you can not

prevent long---time exposure use protective gloves and other protective

clothing.

Keep flammable material away from heat, sparks and open fire.

Hot oil and oil spray can be hazardous. Small amounts swallowed or inhaled

do not usually cause toxication. Old oil is more dangerous than new.

If oil has got into eyes flush them with cool water after which go to doctor.

Use safety goggles.

Avoid mixing lubricants of different grade and quality. Use only recom-

mended oils or oils with corresponding characters.

3.4.SAFETY INSTRUCTIONS FOR THE SEPARATE HYDRAULIC MOTOR USE

Check the moving parts. They should be fastened in place, in good working

condition and all shields and guards must be in place.

Inform everyone who works with the chipper about the risks and how they can

avoid accidents.

Do not let children or incapable persons operate the chipper.Do not wear loose

clothing, loose sleeves, neckties or long uncovered hair around moving parts

of machinery.

Disengage the PTO and turn the tractor off before you service the chipper.

Use only original parts replacements. Do not make any modifications.

Failure to obey the warnings printed on the chipper or in the operator’s manual

might result in a serious injury or death.

When checking the malfunction, all devices must be in “off” position.

Place the PTO shaft in the holding device when disconnected from tractor.

Содержание VALBY CH 260

















































Результаты поиска

Содержание VALBY CH 260

Отзывы:

Farmi Forest Corporation VALBY CH 260, Руководство по эксплуатации, техническому обслуживанию и запасным частям, Страница: 7 / 48

Результаты поиска

Содержание VALBY CH 260

Отзывы: