Farmi Forest Corporation VALBY CH 260 Скачать руководство пользователя страница 15

Страница: 15 / 48

ASSEMBLY AND MOUNTING

CH 260 CHIPPER

www.farmiforest.fi

--- 15 ---

9.LIFTING

Lifting points for each machi-

ne are marked with hook sym-

bols.

CAUTION!

Lift only using the proper type of lifting device

and ensure that it has an appropriate lifting ca-

pacity.
Check the lifting slings, cables, and chains re-

gularly.
Ensure that you know the weight of the load to

be lifted and never exceed the lifting capacity

stated by the manufacturer of the lifting device.
Select the transport routes for lifting so that the

load is not transported over people or a locati-

on where people might be.

CH 260 1124 lbs

without feeder

Fig 3.Lifting point.

10.MOUNTING

10.1.MOUNTING ON A TRACTOR

Attach the drawbar to the outermost holes

of the chipper in order to use as long a

PTO shaft as possible; this increases the

shaft’s service life.

Mount the chipper on the tractor’s 3---point

hitch. If the tractor cannot lift the chipper

up, or if the front of the tractor becomes

too light, move the drawbar to the inner

holes.

Tighten the nuts (M20) to 340 Nm.

The hydraulic feeder and mechanical

feeders include fitting blocks that are

installed between the chipper and feeder.

The fitting blocks are installed so that the

two guide pins located at the bottom

section of the feed opening go through the

holes in the fitting block and secure the

block. See Fig. 4.

Fig 4.Installing the fitting block..

Attach the feed chute, using the pin and

lockscrews, see Fig 5.

Fig 5.Installing the feed shute.

When you work with the chipper, it must be

mounted on a 3---point hitch. The chipper

can tip over if not mounted.

Check that the PTO shaft length is correct.

If the PTO shaft supplied with the chipper

cannot be used, contact your local dealer.

For instructions on shortening the PTO

shaft, see Section 10.1.

Check that the PTO shaft covers are in

place and that the retaining chain for the

shield is attached.

Содержание VALBY CH 260

















































Результаты поиска

Содержание VALBY CH 260

Отзывы:

Farmi Forest Corporation VALBY CH 260, Руководство по эксплуатации, техническому обслуживанию и запасным частям, Страница: 15 / 48

Результаты поиска

Содержание VALBY CH 260

Отзывы: