Farm King Model 1050 Скачать руководство пользователя страница 36

Страница: 36 / 174

Assembly - 10" Backsaver Auger

Tube Assembly

Assemble the tube on a flat level surface.

Figure 30

Install a strap (Item 1) around top tube section (Item

[Figure 30]

Connect the strap to an approved lifting device.
Raise and move the top tube section to the assembly

area.
Place a block under the discharge spout end of the top

tube section. Lower the tube onto the block. Remove

strap.

Figure 31

Install a strap (Item 1) around the center tube section

(Item 2)

[Figure 31]

NOTE: Place a rag (Item 3) [Figure 31] between the

strap and decal to prevent decal damage while

lifting and moving the center tube section.

Raise and move the center tube section to the

assembly area.

•

DO NOT permit bystanders to be in the work area

when unloading and assembling the auger

components.

•

DO NOT work under suspended parts.

•

Keep away from moving parts.

•

Always use lifting devices / vehicles, chains or

straps of adequate size and strength when

unloading and assembling the auger components.

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when

assembling the equipment.

B-0607

B-0608

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды