Mi 2453
Gb - 14 -
Ringing Volume
Ringing volume is the same for all the kind of calls.
-
To adjust it select “Volume” and press
- an adjusting bar is displayed on
the screen - with the buttons
or
adjust the volume - press
- select “save” - press
.
Ringing Tones can be disabled choos-
ing the lowest level of volume in this menu or directly from
the Device Manager menu.
Ringing volume can be also momentarily adjusted acting
on the buttons
or
while receiving a call.
Display Backlighting
Select LCD Backlighting - press
-
chose the desired color from the list or
create a new color - press
- select
“save” - press
.
Display Contrast
Select LCD Contrast - press
- an
adjusting bar is displayed on the screen,
adjust the contrast of LCD acting on the
buttons
or
- press
-
select “save” - press
.
Advanced and System settings
Advanced and system settings are
fundamental
for the
correct working of the system, therefore they are acces-
sible only entering a 4-digit password. From the factory the
password is 1234
. It is advisable to change it with a per-
sonal one
(see chapter “Password changing”).
Attention
. It advisable to write down the new password
and keep it in a safe place; If you lose the password you
must ask a new one directly to ACI FARFISA.
Advanced
To access the advanced menu you should:
Press
- select “settings” - press
- select “advanced”
- press
- enter the 4-digit password - press
- the
following functions will be listed: Password, Relay mode,
Relay timing, Restore factory settings, Clear all bookings,
Delete list, Recovery Directory.
Changing Password
To change the password it is necessary: - select “Password”
– press
- press
to erase the
actual password –enter the new 4-digit
password - press
- select “save”
- press
.
New password in now stored.
Operating mode of the internal relay.
Relay inside the switchboard (terminal boards C, NC, NO)
can be used for:
-
additional ringer
for the incoming calls, a lamp signaller
can also be driven
-
power-ON a CCTV monitor
only during the calls from the
door stations
-
bistable relay
operated by the button ; when the relay
is activated the LED
will light-Up
-
monostable relay
operated by the button ; when the
relay is activated the LED
will light-Up, timing of relay
should be set according the instructions of chapter
“Timing
of internal relay”.
To set the operating mode it is neces-
sary: - select “Relay mode” - press
- select the requested mode - press
- select “save” - press
.
Timing of internal relay
To set the activation time of relay, only when the relay op-
erates as
“additional ringer tone”
and
“monostable”
, it
is necessary: - select “Relay timing” – press
- press
to erase the previous programmed
activation time – enter the new activation
time in seconds (from 1sec to 99 sec.) -
press
- select “save” - press
.
Factory settings
To restore the factory settings and reset all the data previ-
ously programmed (except the directory) it is necessary:
-select “Restore factory settings” - press
- select
YES
to confirm or
NO
to
exit - press
- select “save” - press
.
Clear all bookings
To cancel all the booking queue:
-select “Clear all bookings” – press
- select
YES
to confirm or
NO
to exit -
press
- select “save” - press
.
Erasing completely the directory
To completely erase the directory:
-select “Delete list” - press
- select
YES
to confirm or
NO
to exit - press
- select “save” - press
.
Restoring the users’ in the directory
To restore the last erased directory:
-select “Recovery directory” - press
- select
YES
to confirm or
NO
to exit -
press
- select “save” - press
.
Booking
Mode
- Settings
Menu
Programming system
password
1234
- Addit.ringer tone
Monitor door station
Bistable
Relay mode
####
21.09.11
11.06
Display backlight
- Advanced
Display contrast
Settings
Programming relay time
activation
30
Restore factory set.
NO
YES
Clear ALL bookings
NO
YES
Delete list
NO
YES
Recovery directory
NO
YES
Ringer tones volume
75%
- Red
Green
Blue
Display backlight
Display contrast
50%