Fanvil X7 страница 136 Скачать руководство пользователя

Страница: 136 / 162

125

Table 22 - Dial - up rule configuration table

Parameters

Description

Dial rule

There are two types of matching: Full Matching

or Prefix Matching. In Full matching, the entire

phone number is entered and then mapped per

the Dial Peer rules.

In prefix matching, only part of the number is

entered followed by T. The mapping with then

take place whenever these digits are dialed.

Prefix mode supports a maximum of 30 digits.

Note: Two different special characters are used.

x -- Matches any single digit that is dialed.

[ ] -- Specifies a range of numbers to be matched. It may be a range, a list of ranges separated

by commas, or a list of digits.

Destination

Set Destination address. This is for IP direct.

Port

Set the Signal port, and the default is 5060 for

SIP.

Alias

Set the Alias. This is the text to be added,

replaced or deleted. It is an optional item.

Note: There are four types of aliases.

all:

xxx

ದ

xxx will replace the phone number.

add:

xxx

ದ

xxx will be dialed before any phone number.

del

ದ

The characters will be deleted from the phone number.

rep:

xxx

ದ

xxx will be substituted for the specified characters.

Suffix

Characters to be added at the end of the phone

number. It is an optional item.

Length

Set the number of characters to be deleted. For

example, if this is set to 3, the phone will delete

the first 3 digits of the phone number. It is an

optional item.

This feature allows the user to create rules to make dialing easier. There are several

Содержание X7



































































































































































Результаты поиска

Содержание X7

Отзывы:

Похожие инструкции для X7

Бренды по названию

Популярные бренды

Fanvil X7, Руководство пользователя

Результаты поиска

Содержание X7

Отзывы:

Похожие инструкции для X7

Бренды по названию

Популярные бренды