Fanvil X1S Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 110

background image

95

Default Ring Type

Configure default ringtones. If no special ringtone is set for the phone
number, the default ringtone will be used.

Speakerphone Volume

Set the hands-free volume to 1-9.

Headset Ring Volume

Set the volume of the earphone ringtone to 1~9.

Headset Volume

Set the volume of the headset to 1~9.

Speakerphone Ring Volume

Set the volume of hands-free ringtone to 1~9.

G.723.1 Bit Rate

5.3kb/s or 6.3kb/s is available.

DTMF Payload Type

Enter the DTMF payload type, the value must be 96~127.

AMR Payload Type

Set AMR load type, range 96~127.

Headset Mic Gain

Set the earphone's radio volume gain to fit different models of earphones.

Opus playload type

Set Opus load type, range 96~127.

OPUS Sample Rate

Set Opus sampling rate, including opus-nb (8KHz) and opus-wb (16KHz).

ILBC Payload Type

Set the ILBC Payload Type, the value must be 96~127.

ILBC Payload Length

Set the ILBC Payload Length

Enable MWI Tone

When there is a new voice message message, the phone will start a
special dial tone.

Enable VAD

Whether voice activity detection is enabled.

Onhook Time

Configure a minimum response time, which defaults to 200ms

EHS Type

EHS headset is available after enabling.

RTP Control Protocol(RTCP) Settings

CNAME user

Set CNAME user

CNAME host

Set CNAME host

RTP Settings

RTP keep alive

Hold the call and send the packet after 30s

Alert Info Ring Settings

Value

Set the value to specify the ring type.

Ring Type

Type1-Type9

12.10 Phone settings >> MCAST

This feature allows user to make some kind of broadcast call to people who are in multicast group. User can
configure a multicast DSS Key on the phone, which allows user to send a Real Time Transport Protocol (RTP)
stream to the pre-configured multicast address without involving SIP signaling. You can also configure the
phone to receive an RTP stream from pre-configured multicast listening address without involving SIP
signaling. You can specify up to 10 multicast listening addresses.

«
...
93
94
95
96
97
...
»

Содержание X1S















































































































Отзывы:

Нет отзывов

Похожие инструкции для X1S

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 8

KX-TG7622, KX-TG7623, KX-TG762

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 6

Бренд: Safeline Страницы: 20

Бренд: Panasonic Страницы: 72

Бренд: Newcont Страницы: 14

Бренд: JRC Страницы: 110

Бренд: BT Страницы: 2

Бренд: PhoneMate Страницы: 37

Бренд: Meeteasy Страницы: 2

CENTURION Series

Бренд: NORTHERN ELECTRIC Страницы: 12

80-5727-00 - E5927B - 5.8GHz Dual Handset Answering System

Бренд: AT&T Страницы: 66

Бренд: BT Страницы: 52

Бренд: Hitachi Страницы: 151

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды