Fanvil BW206 Скачать руководство пользователя | Manualshive

Страница: 17 / 38

background image

17

status and network ID is also same as LAN’s, phone will refuse to accept the IP to configure
WAN.

4.3.2.2. QoS Config

The VOIP phone support 802.1Q/P protocol and DiffServ configuration. VLAN functionality can use
different VLAN IDs by

setting signal/voice VLAN and data VLAN. The VLAN application of this phone is

very flexible.

In chart 1, there is a layer 2 switches without setting VLAN. Any broadcast frame will be transmitted to the
other  ports  except  the  send  port.  For  example,  a  broadcast  information  is  sent  out  from  port  1  then
transmitted to port 2,3and 4.
In  chart  2,  red  and  blue  indicate  two  different  VLANs  in  the  switch,  and  port  1  and  port  2  belong  to  red
VLAN,  port  3  and  port  4  belong  to  blue  VLAN.  If  a  broadcast  frame  is  sent  out  from  port  1,  switch  will
transmit it to port 2, the other port in the red VLAN and not transmit it to port3 and port 4 in blue VLAN. By
this means, VLAN divide the broadcast domain via

restricting the range of broadcast frame transmition.

Note: chart 2 use red and blue to identify the different VLAN, but in practice, VLAN uses different VLAN
IDs to identify.

«
...
15
16
17
18
19
...
»

Содержание BW206







































Отзывы:

Нет отзывов

Похожие инструкции для BW206

Бренд: Haier Страницы: 49

blackview Crown

Бренд: Iget Страницы: 76

Бренд: Alcatel Страницы: 53

Бренд: PalmMicro Страницы: 40

Бренд: HTC Страницы: 78

Arcata 28 CIP-D Seires

Бренд: Teltronics Страницы: 2

PowerSeries Neo 3G2080RE

Бренд: DSC Страницы: 44

Бренд: Sagem Страницы: 96

Бренд: Jabbla Страницы: 30

ADR930 Perception

Бренд: Pantech Страницы: 2

Бренд: Viking Страницы: 4

Бренд: Acer Страницы: 66

Бренд: Zte Страницы: 28

Бренд: Zte Страницы: 157

Бренд: Sunstech Страницы: 117

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 16

Anycall GT-B5722C

Бренд: Samsung Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды