Fantic XX 125 Скачать руководство пользователя страница 139

Страница: 139 / 153

4. Maintenance

USE AND MAINTENANCE MANUAL

CHAPTER 4

MAINTENANCE

2-Strokes - Edition 00 / 2023

138

4.9 SHOCK ABSORBER

– Regularly check the upper fastening screw of the shock

absorber “1”. If it is loose, tighten it to the specified torque.

Nut “1”: 56 Nm (5.6 m•kg, 41 ft•lb)

– Regularly check the shock absorber lower fastening screw

“2” and linkage fastening screws “3”, “4” and “5”. If they are

loose, tighten them to the specified torque.

To ensure the best operation and durability of the

rear shock absorber linkage, it is recommended

to check, clean and grease the linkage bearings

periodically.

Nut “2”: 53 Nm (5.3 m•kg, 39 ft•lb)

Nut “3”: 70 Nm (7.0 m•kg, 52 ft•lb)

Nut “4”: 80 Nm (8.0 m•kg, 59 ft•lb)

Nut “5”: 80 Nm (8.0 m•kg, 59 ft•lb)

4.8 FORK

For the maintenance of hydraulic components,

contact an authorised Fantic workshop.

– Regularly check the upper “1” and lower “2” fastening

screws of both stems. If they are loose, tighten them to the

specified torque.

Nut “1”: 21 Nm (2.1 m•kg, 15 ft•lb)

Nut “2”: 21 Nm (2.1 m•kg, 15 ft•lb)

Содержание XX 125


























































































































































Результаты поиска

Содержание XX 125

Отзывы:

Похожие инструкции для XX 125

Бренды по названию

Популярные бренды

Fantic XX 125, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание XX 125

Отзывы:

Похожие инструкции для XX 125

Бренды по названию

Популярные бренды