3
This Manual is Designed to Make it as Easy as Possible for You
to Assemble, Install, Operate, and Maintain Your Ceiling Fan
Unpacking Instructions
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in
fi
nding your place should you be interrupted.
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3-
conductor (2-wire with ground) of the following size:
NOTE:
Place the parts from the loose parts bags in a small con-
tainer to keep them from being lost. If any parts are missing,
contact your local retailer.
Tools Needed for Assembly
Materials
• One Phillips head screwdriver
• One stepladder
• One ¼
˝
blade screwdriver
• One wire stripper
•
Four wire connectors
(supplied)
•
7
⁄
16
˝
,
½
˝
&
9
⁄
16
˝
wrench
or socket wrench
DAMP LOCATION CEILING FAN:
If you have purchased a
Damp Location Ceiling Fan, you may only use light kits marked
suitable for use in damp locations.
Wire Size A.W.G.
Installed Wire Length
14
12
Up to 50 ft.
50 - 100 ft.
NOTE:
If you are uncertain of part description, refer to
parts list/exploded view illustration. (Pages 16,17)
1.
Check to see that you have received the following
parts:
• Hanger Bracket Assembly
• Ceiling Canopy
• 24
˝
Downrod/Ball Assembly
•
Support Bar Assembly
• Two Motor Assemblies
• Two Switch Cup Assemblies
• Blade Holder pack containing:
– Five blade holders (red dot)
– Five blade holders (white dot)
– Ten blade arm covers
• Blade Cover Mounting Hardware Bag
– 3/16
˝
-24 carriage head nut (21)
– 3/16
˝
-24 x 17mm washer-head
screws & fiber washers (21)
• Blade to Motor Hardware Bag
– ¼–20 x 14mm screws with
lockwashers (21)
– Fanimation screwdriver
• 2-speed, C3-CA wall control
Ceiling
Canopy
Hanger Bracket
Assembly
2-Speed
C3-CA Wall Control
Hardware Bag
Blade Holders
(2 sets)
Support Bar
Assembly
NOTE:
The illustration shown is not to scale or its actual con
fi
guration may vary, blade sets are sold separately.
Switch Housing
Assembly (2)
Motor Assembly (2)
24
˝
Downrod Assembly
• Support Cable bag:
– Ceiling Support Cable
– Cable Clamp (3)
– 5
˝
lag bolt
–
3
⁄
8
˝
flat washer
• Hardware bag:
– 2
˝
lag bolt
– 5 mm Allen wrench
– Two
5
⁄
32
˝
–32 x 1
˝
threaded rods
– Two
5
⁄
32
˝
–32 external lockwashers
– Two
5
⁄
32
˝
knurled knobs
– Six motor mounting screws
– One ¼
˝
–20 x 2
1
⁄
8
˝
cap head screw
– One ¼
˝
–20 nylon lock nut
– Four wire connectors
▲
WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
▲
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 8). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
NOTE: Assemble with Hand tools Only!