background image

- 1 -

CP-721-FPV

Voltage relay 

for photovoltaic systems

The CP-721-FPV 1-phase voltage relay is dedicated for photovol-

taic systems. In the event of detecting an excess of the preset 

voltage level, the output relay will switch on, with the help of 

which it is possible to switch on an additional consumer (e.g. 

a boiler), thus increasing the self-consumption of energy in the 

domestic installation and reducing the risk of the photovoltaic 

inverter switching off due to excessively high mains voltage.

»

 Output circuit switched on when voltage is exceeded, swit-

ched off when voltage decreases;

»

 Precise adjustment of switching voltage;

»

 Programmable delay for relay activation and deactivation;

»

 Programmable voltage hysteresis for relay deactivation;

»

 Direct control of loads up to 16 A;

»

 LED display for continuous voltage monitoring.

Purpose

Functions

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: [email protected]

Do not dispose of this device in the trash along with other waste!  

According to the Law on 

Waste, electro coming from households free of charge and can give any amount to up to 

that end point of collec� on, as well as to store the occasion of the purchase of new equip-

ment (in accordance with the principle of old-for-new, regardless of brand). Electro thrown 

in the trash or abandoned in nature, pose a threat to the environment and human health.

Содержание CP-721-FPV









Отзывы: