Falcon RME Series Скачать руководство пользователя страница 5

Страница: 5 / 92

Danger

Warning

Caution

Notice

SAFETY ALERT SYMBOLS AND SIGNAL WORDS

This manual references the words DANGER, WARNING, CAUTION and NOTICE. The level of risk
is indicated by the following signal words. Do not attempt to use the asphalt hot patcher until

reading and understanding

the safety and operational considerations of the equipment.

1
!

DANGER - Immediate hazards which WILL result in
severe personal injury or death if the warning is
ignored.

1
!

WARNING -- Hazards or unsafe practices which
COULD result in severe personal injury or death if
the warning is ignored.

1
!

CAUTION -- Hazards or unsafe practices which
could result in minor or moderate injury if the
warning is ignored.

1
!

NOTICE -- Practices that could result in damage to
the trailer or other property.

Содержание RME Series





























































































Результаты поиска

Содержание RME Series

Отзывы:

Бренды по названию

Популярные бренды

Falcon RME Series, Руководство по эксплуатации, частям и ремонту

Результаты поиска

Содержание RME Series

Отзывы:

Бренды по названию

Популярные бренды