Falcon DAEDALUS Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 20

Falcon DAEDALUS Скачать руководство пользователя страница 8

6

• Plug your 15V 5 amp wall power supply (or your 15V battery)

into the Speed Controller.

• The module should light up and show the current set speed.

Adjust this as necessary using the Up/Down arrows, and then

press the Daedalus logo (Start/Stop) on the Speed Controller.

The display will show “- - -“ which is stopped.

• Attach your fiber to the leader loop. Verify the display says

“---“ which means it is stopped. Flip the direction switch to the

desired direction (I is Z twist, II is S twist).

• When ready, press the Daedalus logo (Start/Stop). The wheel

will slowly accelerate for 3 seconds to your set speed %. You

can fine-tune your speed while spinning by using the Up/Down

arrows. When it’s time to advance your yarn guide, press the

logo (Start/Stop) and the wheel will slowly decelerate for 3

seconds and come to a stop.

• Increase or decrease your speed using the Up and Down

arrows. Pay attention to the takeup and adjust the tension knob

accordingly. Fine-tune your speed as you get comfortable. You

may need to slightly adjust the tension as you change your

speed and as the bobbin fills with yarn.

«
...
6
7
8
9
10
...
»

Содержание DAEDALUS





















Отзывы:

Нет отзывов