English
21
Current Operated Earth Leakage
Breakers
Where the cooker installation is protected by a 30 mil-
liamp sensitivity residual current device (RCD), the
combined use of your cooker and other domestic appli-
ances may occasionally cause nuisance tripping. In these
instances the cooker circuit may need to be protected by
fitting 100mA device. This work should be carried out by a
qualified electrician.
Food is cooking too slowly, too quickly,
or burning
Cooking times may differ from your previous oven. Indi-
vidual tastes may require the temperature to be altered
either way, to get the results you want. Try cooking at a
higher or lower temperature setting.
The oven is not cooking evenly
Do not use a tin or tray larger than 325mm by 305mm for
the main oven or 230mm by 320mm for the Tall oven.
If you are cooking a large item, be prepared to turn it
round during cooking.
If two shelves are used, check that space has been left for
the heat to circulate. When the baking tray is put into the
oven, make sure it is placed centrally on the shelf.
Check that the door seal is not damaged and that the
door catch adjusted so that the door is held firmly against
the seal.
NB the seal on the left hand oven door is intended to have
a gap at the bottom of the door
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered). If the cooker is not level arrange for
your supplier to level it for you.
Oven not coming on when turned on
manually
Is the power on? Is the clock illuminated? If not there may
be something wrong with the power supply. Is the cooker
supply on at the isolator switch? Is the clock flashing
0.00? If so set it to the correct time of day. Has the Timer
been set to AUTO by mistake? If AUTO is showing on the
clock display, press the ‘cook period’ button and reduce
any set cooking time showing to 0.00, with the (+) and (-)
buttons. Press the [ ] button twice. If this does not solve
the problem contact a service person.
Is the key symbol [ ] showing in the display? See the
Clock section of the instructions for more information on
the key lock feature of the clock.
Oven not coming on when automatic
cooking
Timer set correctly but oven knob left OFF by mistake?
Is the key symbol [ ] showing in the display? See the
Clock section of the instructions for more information on
the key lock feature of the clock.
Oven temperature getting hotter as the
cooker gets older
If turning the knob down has not worked or only worked
for a short time then you may need a new thermostat.
This should be fitted by a service person.
Grill not cooking properly
Are you using the pan and trivet supplied with the cooker?
Is the pan being used on the runners, not the floor of the
compartment? Is the grill tray pushed fully back to stop?
The oven light is not working
The bulb has probably blown. You can buy a replacement
bulb (which is not covered under the guarantee) from a
good electrical shop. Ask for an Edison screw fitting 15w
240v lamp, FOR OVENS. It must be a special bulb, heat
resistant to 300°C.
Open the oven door and remove the Handyrack (if fitted)
and oven shelves.
Turn off the power supply.
Unscrew the bulb cover by turning anticlockwise. Unscrew
the old bulb. Screw in the new bulb. Screw on the bulb
cover. Turn on the electricity supply and check that the
bulb now lights.
Hotplate ignition or hotplate burners
faulty
Is the power on? Is the clock illuminated? If not there
maybe something wrong with the power supply.
Are the sparker (ignition electrode) or burner slots blocked
by debris?
Is the burner trim correctly located?
Are the burner caps correctly located?
See the section entitled ‘Cleaning your cooker’
Check that there is not a problem with your gas supply.
You can do this by making sure that other gas appliances
you may have are working.
Do the burners spark when you push the button? If not
check the power is on - is the clock illuminated?
Power failure
In the event of a failure in the electrical supply the hot-
plate may be lit using a match.
General Safety Instructions
This appliance must be installed by a competent person
in accordance with the installation instructions. The instal-
lation must comply with the relevant regulations and also
the local electricity supply company requirements
If you smell gas
Don’t turn electric switches on or off.
Don’t smoke
Don’t use naked flames
Do turn off the gas at the meter or cylinder
Do open doors and windows to get rid of the gas
Call your gas supplier.
