WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
23
Note:
The IHE will require commissioning when the hob has
been refitted.
5.
To Replace a Light Switch
Disconnect from electricity supply.
Remove the control panel (see 3).
Note:
The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the switch
body behind the control panel and twisting sharply. Remove
the switch bezel by folding back its locking wings and pushing
forward. Fit the new bezel to the control panel by first lining
up the raised key on its body with the cut-out in the control
panel and pushing it in from the front.
Assemble the new switch to the bezel by lining up the key
sections and pushing home. Fit the new button by pushing in
from the front.
Replace the Control Panel in reverse order and test for correct
operation.
6.
To Remove the Electronic Timer
Disconnect from electricity supply.
Remove the control panel (see 3). Pull off the timer control
button(s).
Remove the timer/mounting bracket assembly from the
control panel by removing the fixing screws.
Remove the timer from its mounting bracket by depressing
the plastic lugs on the timer case, at the same time pulling the
unit forward.
Reassemble in reverse order. When replacing the leads, refer
to the wiring diagram in this manual. Check the operation of
the timer.
7.
To Replace a Thermostat
Disconnect from the electricity supply.
Lift up the hob (see 2) and remove the control panel (see 3).
Open the oven door. Remove the oven furniture and slide out
the oven roof liner if fitted.
For the right-hand oven, remove the thermostat phial cover
(two screws). Unclip the thermostat phial from the clips in the
oven back.
For the left-hand oven, pull cooker forward to gain access
to the cover box at the rear of the cooker. Remove the four
screws securing the cover and lift clear.
Feed the thermostat capillary out of the oven. Disconnect
the wiring from the thermostat. Remove two screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped to
the oven back with the phial centrally positioned between the
clips.
Check the operation of the thermostat.
8.
To Remove the Grill Door
Remove the left-hand side panel (see 1). Remove the ceramic
hob (see 1). Remove the centre cover strip (5 screws, 2 top, 2
bottom, 1 in middle). Remove the two countersunk screws (1
each side) securing the grill hinge arms to the front of the grill
chamber.
Note:
The arms are spring tensioned. Carefully remove the grill
door. Retain the gaskets.
Reassemble in reverse order ensuring that the gasket is fitted
between the hinge arm and the front of the grill chamber.
9.
To Replace the Grill Controller
Disconnect from electricity supply.
Lift up the hob (see 2) and remove the control panel (see 3).
Disconnect the wiring from the controller. Remove the two
screws holding the controller to the mounting panel. Fit the
new controller and reassemble in reverse order. Check for
correct operation.
10. To Remove the Grill Element
Disconnect from electricity supply.
Remove grill pan from inside the grill compartment; remove
the enamelled front shield from the grill roof, by undoing the
two screws and washers.
Remove the two screws and washers securing the grill
element front support. Remove the screws from the grill
element.
Lift the element out carefully, disconnecting the leads from
the element terminals (noting their position). If it is not
possible to disconnect the leads in this way, pull the cooker
forward to gain access to the rear, remove the screws securing
the electric cover to the back sheet, remove the cover and
disconnect the terminals from the rear.
Fit the new element and reassemble in reverse order. Check
the operation of the grill.
11. To Replace an Oven Door
Open the oven door. Support the door and remove the two
screws securing the upper hinge and gasket to the cooker
front
(Fig.7-3)
. Remove the door from the lower hinge by
lifting slightly and moving outwards
(Fig.7-4)
.
The door is heavy, so take care.
Reassemble in reverse order.
12. To Adjust an Oven Door Angle
The bottom hinge of either oven door can be adjusted to alter
the angle of the door
(Fig.7-5)
. Loosen the bottom hinge
fixing screws and use the notch and a flat bladed screwdriver
to move the position of the hinge to set the hinge position
(Fig.7-6)
.
Retighten the hinge screws.
13. To Replace an Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel fixing
screws from the door sides – two each side
(Fig.7-7)
.
Carefully lift off the outer door panel.
Remove the door handle from the panel by unscrewing the
two retaining nuts. Fit the door handle to the new panel.
Fit the panel to the door. Reassemble in reverse order.
