7 M-85E0-F O81121
4
Set-up examples
1
Setting the XFE for large pump application
With
‘Starter Disabled’
shown on the display, press
ENTER
key once.
!
With
‘Applications’
shown on the top line of the
display press
ENTER
once.
#
With
‘Settings’
shown at the top of the display press
"
"
"
"
"
key three times until
‘Large pump’
is shown at
top of display.
$
Press
ENTER
once to select large pump. The
display will indicate the parameters changing in
short intervals.
%
With the display top line indicating
‘Send to store?’
,
press
ENTER
to save the settings for a large pump
to permanent store. Display will flash the message
‘Storing’
twice to indicate this has been done.
&
At any of the above stages pressing
#
will return the user to the previous menu. The XFE will not start until
the control display indicates
‘Stopped and ready’.
Applications
Auto features
Settings
Default (keypad)
Send to store?
#=no Enter=yes
Large Pump
Conveyor
ENTER
#
#
#
ENTER
ENTER
ENTER
Starter Disabled
1:
q
to Enable
2
Setting the XFE for remote starting and stopping.
With
‘Starter Disabled’
shown on the display,
press
ENTER
key once.
!
With
‘Applications’
shown on the top line of
the display press
"
"
"
"
"
key twice until
‘Basic’
is
shown at the top of the display.
#
Press
ENTER
once to select Basic menu.
$
Press
"
"
"
"
"
key twice until
‘Starting’
is shown at
top of the display then press
ENTER
once to
select starting option menu.
%
With display now indicating
‘Starting’
on top line
press
ENTER
to toggle from
‘Keypad Starting’
to
‘Remote Starting’
as shown on bottom line
of display.
&
At any of the above stages pressing
#
will return
the user to the previous menu.
The XFE will now start and stop remotely from the START and STOP switches shown in Figure 2.1, but will return to
keypad starting if the control supply on terminals X1 and X2 is removed. Alternatively, to return to keypad starting and
stopping, repeat the above procedure and select
‘Keypad Starting’
at step 5.
To keep the remote start/stop setting
after removal of the control supply, the settings must be permanently saved (See 3 below).
Applications
Auto features
ENTER
#
#
#
ENTER
ENTER
ENTER
Basic
Advanced
Starting
Keypad starting
Starting
Remote starting
ENTER
Disable starter
Enable starter
Starting
Starter Disabled
1:
q
to Enable
3
Permanently saving parameters set by user.
With
‘Starter Disabled
shown on the display, press
ENTER
key once.
!
With
‘Applications’
shown on the top line of the
display press
"
"
"
"
"
)
)
)
)
)
key four times until
‘Permanent
Store’
is shown at top of display.
#
Press
ENTER
once to select Permanent Store menu.
$
With
‘Save Param’
shown at top of display press
ENTER
once to permanently save parameters.
Display will flash twice to indicate this has been done.
%
At any of the above stages pressing
#
will return the
user to the previous menu.
Save parameter
Po
w
er on param
ENTER
#
#
ENTER
ENTER
Permanent store
Pass
w
ord
Applications
Auto features
Starter Disabled
1:
q
to Enable
The XFE should always be
disabled
before making changes. The Soft Starter then remains unable to drive the
load until it has been
enabled
via the
Basic Menu
, or the control supply is removed and reapplied, or the
key
is pressed when prompted. If the Remote Start/stop is active the XFE cannot be
enabled
.
