background image

 

20

13

 

DELIMING 

In order to maintain dishwasher at optimum conditions, it is requested to remove lime and corrosion 
deposits on a frequent basis. A deliming solution should be available from your chemical supplier. 
Read and follow all instructions on the label of the deliming solution.  Operations: 
 

 

Fill the machine. Add the correct amount of deliming solutions as recommended by the 
deliming solution manufacturer. The water capacity of the tank can be verified on the 
specification sheet of this manual 

 

Remove detergent and rinsing tubes from containers so no chemicals go to the machine 

 

Run the machine for the recommended period of time. As many cycles as needed. 

 

Turn off the machine and open the door 

 

When clean, drain and re-fill the machine 

 

Run machine for 3-4 cycles to remove deliming solution 

 

Drain the machine. 

 

 

14

 

RECOMMENDED SPARE PARTS 

 

Part number 

Description 

P255001 

Water fill valve (dual) 

R223005 

Tank heating element 2000 W. 

Z203009 Door 

switch 

Z203062 

Door relay  

Z211903 

Rinsing nozzle  

Z213007  

Contactor  

Z393005 Boiler 

thermostat 

Z400709 

Washing nozzle  

Z400711 

Washing nozzle bracket  

Z401001 Pump 

motor 

60Hz. 

Z421711 

Boiler heating element 2800W. 

Z433011 Pressure 

switch 

Z448302 Timer 
Z718441 Tank 

thermostat 

Z433001 

General selector switch 

Z223501 Drain 

pump 

V817100 

6 MF Capacitor 

Q307051 

Gasket for Overflow Tube 

Z400907 Overflow 

Tube 

Z231105 Antireturn 

valve 

U183046 Terminal 

Block 

Z200107 Adjustable 

Leg 

Z651123 

Rinse Aid Dispenser 

1200000132 

Detergent Pump Kit 

 

Содержание LVC-21W

























Отзывы: