fadini Siti 63, Инструкция по эксплуатации, Страница: 21 / 48

Deleting a Transmitter A means deleting its key-code from the Radio Receiver, using the Birio LC Device as an alternative to operation on page 9. For this
operation on the Birio LC Device, any transmitter can be used (either clear or key-encoded), even the same transmitter, which will be used as a deleting
"carrier B" to accomplish this operation on the Radio Receiver.
When the operation is completed the Tansmitter
"carrier B" will have deleted Transmitter A but will not replace it.
If an "Error" message is displayed it means that the operation was not correctly carried out, or that the transmitter is encoded with
a key-code belonging to a different family.
1°
Follow the operation transmitter data reading, page 14, for the transmitter A to
be deleted.
NOTE: only Transmitter A code is needed for the deletion,in this way it is possible
to follow the operation as described on page 21.
3°
page 19
Operate near the power supplied Radio Receiver (max distance 10
metres) and push one button on transmitter B for 4-5 times as long as the
led will illuminate.
When the operation is achieved, Transmitter B has accomplished its
function.
AERIAL
1
2
3
4
5
1°R
2°R
Transmitter B
Transmitter A to
be deleted
A
B
A
2°
Push the 4th multi-function button:the functions Copy, Replace,Delete and Copy
one button are sequencely displayed. To confirm press again this 4th button when
the operation required is displayed . Then position the transmitter B(information
carrier) onto the Birio LC Device to learn the information to accomplish the
operation.
Check the operation: remove transmitter B and press one button, the
messages "Pulse Transmission" and "Delete" will be displayed as a confirmation
Copying a Transmitter A means creating a new Transmitter B which, in order to be stored inside a Memory, uses an existing Transmitter A to enter
Memory. Both transmitters are different and have different codes.
This operation is possible with blank or key-encoded transmitters (in this case also the memory must be key-encoded).
If an "Error" message is displayed it means that the operation was not correctly carried out, or that the transmitter is encoded with a
key-code belonging to a different family.
3°
IMPORTANT: If by mistake a button on the transmitter B is pushed once or more times, before the Radio Receiver learning, or the operation is not correctly
carried out,or the same operation needs to be carried out on other installations (page 27), 4 more possibilities will be given to repeat the operation, if all
the 5 possibilities are used up it is possible to reactivate them by pressing the 1st button on the Transmitter for 20 seconds (after 5 seconds the led will turn
off) , release when the Led will light again.
page 17
AERIAL
1
2
3
4
5
1°R
2°R
B
Transmitter B
A
B
1°
Follow the operation transmitter data reading, page 14, for the transmitter A to be
copied.
NOTE: only Transmitter A code is needed for the copy,in this way it is possible to
follow the operation as described on page 21.
Transmitter A to be
copied
A
2°
Push the 4th multi-function button:the functions Copy, Replace,Delete and Copy
one button are sequencely displayed. To confirm press again this 4th button when
the operation required is displayed . Then position the transmitter B onto the Birio
LC Device to learn the information to accomplish the operation.
Check the operation: remove transmitter B and press one button, the
messages "Pulse Transmission" and "Copy" will be displayed as a confirmation
Operate near the power supplied Radio Receiver (max distance 10
metres) and push one button on transmitter B for 4-5 times as long as
the led will illuminate.
The operation completed, Transmitter B has accomplished its function.
DISPLAY
Copy
Transmitter
Enter Transmitter
DISPLAY
DeleteTransmitter
Enter Transmitter
TRANSMITTER COPYING
TRANSMITTER DELETING FROM THE RADIO RECEIVER
IIMPORTANT: If by mistake a button on the transmitter B is pushed once or more times, before the Radio Receiver learning, or the operation is not correctly
carried out,or the same operation needs to be carried out on other installations (page 27), 4 more possibilities will be given to repeat the operation, if all
the 5 possibilities are used up it is possible to reactivate them by pressing the 1st button on the Transmitter for 20 seconds (after 5 seconds the led will turn
off) , release when the Led will light again.
TRANSMITTER
DISPLAY
TRANSMITTER
DISPLAY
REPLACE
DELETE
COPY ONE BUTTON
COPY
MEMORY ENTER
KEYS
DELETE
KEYS
SELECT
CODE
REPLACE
DELETE
COPY ONE BUTTON
COPY
MEMORY ENTER
KEYS
DELETE
KEYS
SELECT
CODE
Siti
Siti