fadini FOX 724, Инструкция по эксплуатации и обслуживанию

Страница: 20 / 56

GB
- 20
INDEX
1. GENERAL WARNINGS
2. PRODUCT DESCRIPTION AND INTENDED USE
3. PACKAGE CONTENTS
4. PRODUCT COMPONENT DESCRIPTION
5. TYPE OF SYSTEM
6. INSTALLATION
6.1 Tools and materials
7. MAINTENANCE
7.1 Periodic maintenance
8. PRODUCT TECHNICAL DATA SHEET
8.1 Technical data
9. LIMITATIONS OF USE
10. DECLARATION OF CONFORMITY
1. GENERAL WARNINGS
THANK YOU
Thank you for purchasing a Fadini product.
Please read these instruc ons carefully before using this
appliance. The instruc ons contain important informa on
which will help you get the best out of the appliance and ensure
safe and proper installa on, use and maintenance. Keep this
manual in a convenient place so that you can always refer to it
for the safe and proper use of the appliance.
INTRODUCTION
This operator is designed for a specific scope of applica ons as
indicated in this manual, including safety, control and signaling
accessories as minimum required with Fadini equipment. □ Any
applica ons not explicitly included in this manual may cause
opera on problems or damages to proper es and people. □
Meccanica Fadini S.r.l. is not liable for damages caused by the
incorrect use of the equipment, or for applica ons not included
in this manual or for malfunc oning resul ng from the use of
materials or accessories not recommended by the
manufacturer. □ The manufacturer reserves the right to make
changes to its products without prior no ce. □ All that is not
explicitly indicated in this manual is to be considered not
allowed.
BEFORE INSTALLATION
Before commencing operator installa on assess the suitability
of the access, its general condi on and the structure. □ Make
sure that there is no risk of impact, crushing, shearing,
conveying, cu ng, entangling and li ing situa ons, which may
prejudice people safety. □ Do not install near any source of heat
and avoid contacts with flammable substances. □ Keep all the
accessories able to turn on the operator (transmi ers,
proximity readers, key-switches, etc) out of the reach of the
children. □ Transit through the access only with sta onary
operator. □ Do not allow children and/or people to stand in the
proximity of a working operator. □ To ensure safety in the whole
movement area of a gate it is advisable to install photocells,
sensi ve edges, magne c loops and detectors. □ Use
yellow-black strips or proper signals to iden fy dangerous
spots. □ Before cleaning and maintenance opera ons,
disconnect the appliance from the mains by switching off the
master switch. □ If removing the actuator, do not cut the
electric wires, but disconnect them from the terminal box by
loosening the screws inside the junc on box.
INSTALLATION
All installa on opera ons must be performed by a qualified
technician, in observance of the Machinery Direc ve
2006/42/CE and safety regula ons EN 12453 - EN 12445. □
Verify the presence of a thermal-magne c circuit breaker 0,03 A
- 230 V - 50 Hz upstream the installa on. □ Use appropriate
objects to test the correct func onality of the safety
accessories, such as photocells, sensi ve edges, etc. □ Carry out
a risk analysis by means of appropriate instruments measuring
the crushing and impact force of the main opening and closing
edge in compliance with EN 12445. □ Iden fy the appropriate
solu on necessary to eliminate and reduce such risks.□ In case
where the gate to automate is equipped with a pedestrian
entrance, it is appropriate to prepare the system in such a way
to prohibit the opera on of the engine when the pedestrian
entrance is used. □ Apply safety nameplates with CE marking on
the gate warning about the presence of an automated
installa on. □ The installer must inform and instruct the end
user about the proper use of the system by releasing him a
technical dossier, including: layout and components of the
installa on, risk analysis, verifica on of safety accessories,
verifica on of impact forces and repor ng of residual risks.
INFORMATION FOR END-USERS
The end-user is required to read carefully and to receive
informa on concerning only the opera on of the installa on so
that he becomes himself responsible for the correct use of it. □
The end-user shall establish a wri en maintenance contract
with the installer/maintenance technician (on -call). □ Any
maintenance opera on must be done by qualified technicians.
□ Keep these instruc ons carefully.
WARNINGS FOR THE CORRECT OPERATION OF THE
INSTALLATION
For op mum performance of system over me according to
safety regula ons, it is necessary to perform proper
maintenance and monitoring of the en re installa on: the
automa on, the electronic equipment and the cables
connected to these. □ The en re installa on must be carried
out by qualified technical personnel, filling in the Maintenance
Manual indicated in the Safety Regula on Book (to be
requested
or downloaded from the site
www.fadini.net/supporto/downloads). □ Operator:
maintenance inspec on at least every 6 months, while for the
electronic equipment and safety systems an inspec on at least
once every month is required. □ The manufacturer, Meccanica
Fadini S.r.l., is not responsible for non-observance of good
installa on prac ce and incorrect maintenance of the
installa on.
DISPOSAL OF MATERIALS
Dispose properly of the packaging materials such as cardboard,
nylon, polystyrene etc. through specializing companies (a er
verifica on of the regula ons in force at the place of installa on
in the field of waste disposal). Disposal of electrical and
electronic materials: to remove and dispose through
specializing companies, as per Direc ve 2012/19/UE. Disposal
of substances hazardous for the environment is prohibited.
FOX 724 | FOX 730
CE DECLARATION OF CONFORMITY of the manufacturer:
Meccanica Fadini S.r.l. (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that: FOX complies with the 2006/42/CE Machinery Direc ve, and
also that it is sold to be installed in an “automa c system”, along with original accessories and components as indicated by the manufacturing company. An automa c gate
operator is, by law, a “machinery” and therefore the installer must fit the equipment with all of the applicable safety norms. The installer is also required to issue the
installer’s Declara on of Conformity. The manufacturer is not liable for possible incorrect use of the product. The product complies with the following specific norms:
analysis of the risks and subsequent ac on to cure them as per EN 12445 and EN 12453, Low Voltage Direc ve 2014/35/UE, Electromagne c Compa bility 2014/30/UE.
In order to cer fy the product, the manufacturer declares under own responsibility the compliance with the EN 13241-1 PRODUCT NORMS.
Tested and cer fied: marking and type tes ng according to ITT PDC No. 2392-2008.
The CE conformity declara on can be downloaded from the website www.fadini.net.
President of the Board
Meccanica Fadini S.r.l.
Paolo Fadini