manualshive.com logo in svg

Factor Electronics HDBaseT-4x4Matrix, Инструкция по эксплуатации

Поделиться
Скачать
Factor Electronics HDBaseT-4x4Matrix Скачать руководство пользователя страница 2

 

2 

www.factorelectronics.com 

HDBaseT-4x4Matrix 

Factor Electronics 

 

Thank you for purchasing this product. For optimum performance and safety, please read 

these instructions carefully before connecting, operating or adjusting this product. Please keep 

this manual for future reference.   

 

 

SURGE PROTECTION DEVICE RECOMMENDED 

This  product  contains  sensitive  electrical  components  that  may  be  damaged  by  electrical 

spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly 

recommended in order to protect and extend the life of your equipment. 

 

 

 

SAFTY NOTICE 

1.  The transmission distances of HDMI over UTP cables aremeasured using TE 

CONNECTIVITY 1427071-6 

2. 

EIA/TIA-568-B termination (T568B) for CAT cables is recommended for better 

performance. 

3.  DO NOT use 568A/568B standard mixed CAT cable (cross-over cable) because there are 

2 pairs swapped, this will make POE OVER-CURRENT and damage POE components. 

Please use straight-through CAT cable (both RJ45 headers are 568A or 568B standard). 

4.  It is recommended that power up the device after connections of source, sinkand CAT 

cable. 

5.  To reduce the interference among the unshielded twisted pairs of wires in CAT cable, do 

not run HDBaseT / Zone Cat5e/6/6a cabling with or in close parallel proximity to mains 

power cables.ShieldedCAT cables can be used to improve EMI problems, which is worsen 

in long transmission.   

6.  Because the quality of the CAT cables has the majoreffect on how long the transmission 

limit can achieve and how good is the received picture quality, the actual transmission 

range is subject 

to one’s choice of CAT cables.   

7.  Do not substitute or use any other Power Supply other than the enclosed unit, or a Factor 

Electronicsapproved Replacement Part.Doing so will void the warranty and potentially 

expose the user to dangerous voltages resulting in an electrical shock.   

8.  Do not disassemble the device 

for any reason. Doing so will void the manufacturer’s 

warranty. Also, our unique case is an integral part of the design of this unit and is 

responsible for cooling and circuitry shielding. Any modifications to this case will 

potentially cause malfunction and product failure.   

9.  Do not expose the device to water, moisture, or liquids.Possible electric shock may result 

as well as failure of the unit to operate. 

Содержание HDBaseT-4x4Matrix


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды