Faber Nova, Руководство по установке

Страница: 4 / 12

Version 11/00 - Page 4
INSTALLATION DIMENSIONS
The Nova chimney is adjustable and designed to meet varying
ceiling heights. FIGURE 2 illustrates the standard installa-
tion for the Nova which requires the canopy to be mounted
24" above the countertop. The chimney can be adjusted for
ceilings between 8 feet and 9 feet.
TOOLS NEEDED FOR INSTALLATION
• Saber Saw or Jig Saw
• Drill
• 1 1/4" Wood Drill Bit
• Pliers
• Phillips Screwdriver
• Flat Blade Screwdriver
• Wire Stripper or Utility Knife
• Metal Snips
• Measuring Tape or Ruler
• Level
• Pencil
• Caulking Gun
• Duct Tape
PARTS SUPPLIED FOR INSTALLATION
• 1 Hardware Package
• 1 Literature Package
PARTS NEEDED FOR INSTALLATION
• 2 Conduit Connectors
• Power Supply Cable
• Wiring Cable - Optional Remote Blower Only
• 1 Wall or Roof Cap
• All Metal Ductwork
RANGEHOOD ASSEMBLY
B -
C -
S -
I -
1 -
2 -
3 -
OPTIONAL BACKSPLASH
CANOPY
UPPER CHIMNEY
LOWER CHIMNEY
LOWER BRACKET
UPPER BRACKET
MIDDLE CHIMNEY BRACKET
FIGURE 1
FIGURE 2
CALCULATE THE DUCTRUN LENGTH
The ductrun should not exceed 35 feet if ducted with 3 1/4"
by 10" rectangular duct and 60 equivalent feet if ducted with
9" round ductwork. Calculate the length of the ductwork by
adding the equivalent feet in FIGURE 3 for each piece of duct
in the system An example is given in FIGURE 4. For best
results, use no more than three 90° elbows. Make sure that
there is a minimum of 24" of straight duct between elbows if
more than one is used. Do not install two elbows together.
Remote blowers require 9" round duct.
WARNING
Because of the weight and size of the rangehood
canopy, two or more people are needed to move
and safely install the rangehood canopy.
Failure to properly lift rangehood could result in
damage to the product or personal injury.
PERSONAL INJURY HAZARD
9 Feet Straight Duct
2 - 90˚ Elbows
Wall Cap
Total System
9.0 feet
10.0 feet
0.0 feet
19.0 feet
FIGURE 4
7.0 feet
5.0 feet
12.0 feet
0.0 feet
45˚ Elbow
90˚ Elbow
90˚ Flat Elbow
Wall Cap
FIGURE 3
PLAN THE INSTALLATION
This rangehood can be installed as either ducted or ductless.
The blower can be vented through the wall or ceiling. To
vent through a wall, a 90° elbow is used. When installed
ductless, the rangehood vents out of grates on the sides of
the chimney. Ductless installations require a Ductless Kit,
available from your dealer.
This rangehood can be used with an optional remote blower.
If a remote blower is used, then the internal blower must be
removed and discarded. Both blowers cannot be used together.
The remote blower connects to the rangehood using a separate
wiring cable not supplied with the rangehood. The wiring cable
should be installed at the same time as the ductwork.
WARNING! BEFORE MAKING ANY CUTS OR HOLES
FOR INSTALLATION, DETERMINE WHICH VENTING
METHOD WILL BE USED AND CAREFULLY CALCULATE
ALL MEASUREMENTS.
9 1/2"
Min. - 1"
Max. - 20"
upper
chimney
cover
22"
cabinet
base
24"
36"
lower
chimney
cover
canopy
Min. 92 1/2"
Max. 111 1/2"
19 1/4"
!