Faber MatriX 800/500 RD H, Руководство по установке

Страница: 11 / 36

Installation manual MatriX 800-1050x500 RD,ST H
10 < < < <
the proximity of the appliance, which must always
be freely accessible. Position the gas connection so
that it is easily accessible for service and the
burner unit can be disassembled at any time.
4.2 Electrical connection
The fire is equipped with two plugs, one for the
HPL unit and one for the gas control system
Place a double wall socket 230VAC - 50Hz near the
fire for connecting the Control box FAB1806.
See fig. 1.4 for the wiring diagram:
(Intelligent Technical Controller)
B = Electronics
C = Gas valve
D = Solenoid valve
E = HPL module (Hybrid Power Light)
F = Ignition pin
G = Ionization pin
H = Power cable
I = Configuration plug
4.3 Smart Home installation
The controller can be connected to an external
source, such as a Domotica system, by using a
Faber Interface Unit (article number A9323000).
4.4 Preparing the fireplace

Remove the fireplace from its packaging.
Ensure that the gas supply pipes under
the appliance are not damaged.

Remove the glass and any mouldings,
store them at a safe place and remove the
packaged parts from the fireplace.

Prepare the gas connection on the gas
valve.
4.5 Setting the restrictor plate
The flu calculation indicates which restrictor plate
setting is required for the correct operation of the
fireplace. See chapter 11 flue calculation.
The restrictor plate has a scale from 0 to 110 in
steps of 10. Standard the restrictor value is set to
60. (See fig. 1.5b and 1.6).
To get good access to the restrictor, you can
consider sliding out the top plate, even with the
top plate there is a good access to the restrictor.
See Fig. 1.5a.
Loosened the two screws to adjust the restrictor
plate. Move the restrictor plate to the left and
slide it to the correct setting. Tighten the screws.
When the calculation shows 0, the restrictor must
be set to the top position.
When the calculation indicates 110, the restrictor
should be set to the bottom position.
For all other values the intermediate positions
must be used.
4.6 Positioning the fireplace
Take into account the installation requirements
(see chapter 3). Place the fireplace at the right
place and level it.
Rough height adjustment:

With the adjustable (optional) legs.
Accurate height adjustment:

With the adjustable feet.
4.7 HPL module (Hybrid Pro Light)
Place the power supply of the HPL module in a cool
place and close to the controller (see fig. 1.7).

Please note!
Before the chimney breast is placed, a functional
test of the HPL module is recommended.
Physical control:
Switch on the HPL module with the remote control
and check whether the LED lamps are on (see
fig.1.8).
Check HPL module electronically in the ITC-V2
App: (only possible in dealer setting)
Make sure the ITC-V2 app is connected to the fire.
See fig 1.9a.
1.
Enable the glow effect on the start screen of
the ITC-V2 APP see fig. 1.9b
2. Navigate to:
3. Menu (top left), diagnostics, current measured
values, experience module.
4. Click on “Test LED spots” see fig. 1.9c
If there are spots defective, this will be indicated in
the App, use for the position the over-view in
section 16 t / m 16.3.
Testing Section burners, step valves:
Activate by the “step symbol” in the start screen
the sectional burner. Switch the various modes.
See fig. 1.9d.
If a valve is defective, this will be indicated in the
App.
4.8 Installing the flue pipes
Install the flue pipes according to the installation
manual supplied with the appliance (40011968)!