Faber I.T.C., Руководство пользователя

Страница: 10 / 32

E N G
- U s e r m a n u a l
1 Dear user
Congratulations on purchasing your Faber product, a quality
product that will provide you with warmth and atmosphere for many
years. Please read the user manual before using the fire. Should,
despite the careful final checks, a malfunction occur, please contact
your Faber dealer.
2 Check
Check the fire for transport damage and report any damage
immediately to your dealer.
3 Introduction
> Please note:
This fire produces heat which will promote air circulation. For this
reason, it is important that you do not use the fire shortly after a
room or house renovation. Moisture and volatile compounds from
freshly applied paint, building materials, floor coverings etc. may be
circulated in the airstream. Compounds may be deposited on cold
surfaces as soot. Consult your gas fitter for more information on
using the product for the first time.
4 Safety instructions for the user
The appliance has been designed for atmospheric and heating
purposes. This means that all surfaces of the fire, including the
glass, can become very hot (hotter than 100°C). An exception to
this is the bottom of the fire and the controls.
• If the fire has been switched off, wait for at least three
minutes before re-igniting it again.
• If the fire switches off with no known cause, wait for at least
15 minutes before re-igniting the fire again. If this happens
repeatedly, contact your gas fitter.
• The fire should not be used if the glass is damaged, has
been removed or if the combustion chamber is open.
• Do NOT place any flammable materials in the combustion
chamber.
• Never change the position of the log set or add more
decorative materials than have been supplied with the fire.
When the fire is switched on, the pilot flame should always be
visible.
• Do NOT place curtains, clothes, laundry, furniture or any
other flammable materials in the vicinity of the appliance. The
minimum safe distance to combustible materials is 1 m.
4.1 Using the fire for the first time
Before ignition, remove all stickers, protective wrappings and, if
present, rubber protective padding from the glass. Make sure the
room is properly ventilated the first time the fire is switched on.
Burn the fire on the highest setting for some hours so that the
lacquer coating will have an opportunity to set and possible vapours
released can be safely removed by ventilation. Keep children and
pets outside the room during this process!
4.2 Cleaning and maintenance
The fire must be serviced, cleaned and checked for suitable
operation by a qualified person (usually the installer) once a year.
The outside of the fire can be cleaned with a clean, damp cloth.
4.3 Cleaning the glass
Remove the glass as described in the installation manual.
Remove all deposits with a clean, dry cloth. If necessary a special
ceramic hob cleaner can be used.
> Please note:
Avoid leaving fingerprints on the glass. These may be baked on by
the heat and may then no longer be removable.
5 General I.T.C.
(Intelligent Technical Controller)
The Faber I.T.C. has the following functions:
1. Operating
2. Checking
3. Registration
4. Advising
5. Controlling
The fire can be operated via a Smartphone or tablet with Android
4.01 and higher or IOS operating system in combination with the
free downloadable Faber I.T.C. App. Limited operation is also possi-
ble with the supplied remote control.
5.1 Remote control
The remote control can only be used for basic functions such as
switching on/off, flame height, selecting the step function and
switching light effect on/off.
5.2 Smartphone or tablet
Almost all functions are available through Wi-Fi, internet connection
is not required. For 100% functionality both Wi-Fi and internet
connection are required. The options of the I.T.C can be fully
utilized via a Smartphone or tablet. In addition to the standard
functions, the ECO and Thermostat function are also available via
these devices.
5.2..1 ECO and ECO+ function
ECO: the automatically modulating burner mimics the behaviour of
a log fire. You can choose between 5 energy-saving programs.
ECO+ mode: The I.T.C. anticipates the room temperature and the
ECO mode selected by you. The I.T.C. sets the fire to the most
economical mode. This creates the optimal flame at minimum gas
consumption.
5.2.2 Thermostat function
The thermostat function brings the room to the desired temperature
and then maintains this.
1 0