![background image](http://html1.mh-extra.com/html/faac/e124/e124_manual_3113221015.webp)
3
DL 2
DL
DL 3
DL 2
DL
DL 3
DL 2
DL
DL 3
DL 2
DL
DL 3
ENGLISH
7.
PROGRAMMING
To program the operation of the automated system, you must
access the “PROGRAMMING” mode.
Programming is in two parts: st LEVEL, 2nd LEVEL.
On activation of the board, the display shows
bo and, for 3 seconds, the fw version of the
board.
The status of the automated system is shown
on the display. If “PC” appears on the display
when the F push-button is pressed, this means
that programming with the PC is loaded on the
board. If no password was set, you can only
modify parameters
Lo
-
PA
-
Pb
. To modify the
other programming parameters, reload the
default of the motor used (in this case the PC
programming will be replaced by the default
parameters of the board)
If dF appears on the display when you press
key F (and hold it down), this means that you
have entered 1st level programming (see
parag. 7.1).
Modification of the programming
parameters is immediately effective, whereas
definitive memory-storage occurs only on
exiting programming and returning to the
view of the inputs status. If you cut power to
the equipment before returning to view the
inputs status, all the modifications made will
be lost.
You can return to the inputs status display,
and save all the parameters modified up
till then, from any point of 1st and 2nd level
programming by simultaneously pressing keys
F
and
-
.
To restore the default settings, recharge the
required default during the first passage of 1st
level programming.
7.1. 1
ST
LEVEL PROGRAMMING
If
PC
appears when you press any button on the display, this means that programming from the PC with a protection password
is loaded on the board. Nothing can be modified without the PC and relevant protection password. Connect the PC to the uSB
to view and/or modify programming, using the dedicated instruction.
Press push-button
F
to access
st
level programming.
If you press key
F
(and hold it down) the name of the function appears on the display.
If you release the push-button, the display shows the value of the function, which can be changed with keys
+
and
-
.
If you press
F
again (and hold it down), the display shows the name of the next function, etc.
When you have reached the last function, press key
F
to exit programming and save the parameters. The display resumes
showing the automated system status.
•
•
•
•
ENCODER WIRING FOR OPERATOR S450H
*
LEAF 1 OPENS AS FIRST AND CLOSES AS SECOND.
IF THERE IS NO REBATE BETWEEN LEAF 1 AND 2,
SET THE LEAF DELAY TO ZERO ON THE CONTROL
BOARD.
REVERSE THE ENCODER WIRES TO EXCHANGE
BETWEEN THE ENCODER ASSOCIATED WITH LEAF
1 AND THE ENCODER ASSOCIATED WITH LEAF 2,
AND VICE VERSA
THROUGH THE BRACKET COVERING
HOUSING MAKE SURE THAT LED DL1 IS
LIGHTED ON LEAF 2, WHEN THE MOTOR
IS AT REST
LEAF 2
ONE LED ON
THROUGH THE BRACKET COVERING
HOUSING, MAKE SURE THAT LEDs DL1
AND DL2 ARE LIGHTED ON LEAF 1,
WHEN THE MOTOR IS AT REST
LEAF 1
TWO LEDs ON
LEAF 1*
THROUGH THE BRACKET COVERING
HOUSING MAKE SURE THAT LED DL1 IS
LIGHTED ON LEAF 2, WHEN THE MOTOR
IS AT REST
LEAF 1
TWO LEDs ON
LEAF 2
ONE LED ON
THROUGH THE BRACKET COVERING
HOUSING, MAKE SURE THAT LEDs DL1
AND DL2 ARE LIGHTED ON LEAF 1,
WHEN THE MOTOR IS AT REST
LEAF 1*
ENCODER WIRES REVERSING OPERATION
ENCODER
LEAF 1
ENCODER
LEAF 2
LEAF 2
LEAF 2