FAAC 770 N, Руководство пользователя

Страница: 4 / 12

770 N 4 732615 - Rev.A
ENGLISH
Translation of the original instructions
3.
Close the containment frame as shown in fig.13 and 14.
4.
Weld the leaf containment frame to the leaf support frame, fig.15.
5.
Assemble all parts as shown in fig.16.
6.
Carefully grease the rotation pin and the ball.
Do not grease the release device.
7.
Position the leaf and secure the upper hinge.
8. Manually move the leaf to ensure correct positioning.
9.
Secure the leaf to the containment frame using a through screw, fig.17.
Do not weld the leaf to the containment frame.
4.5 INSTALLING THE GEARMOTOR
1.
Place
the gearmotor in the box as shown in
fig.18, using
the provided
handle ref. for handling.
To correctly position the gearmotor, refer to figure 19. In any case,
the gearmotor transmission shaft must be on the side opposite gate
opening.
2.
Secure the gearmotor using the provided nuts and washers.
3.
Install the transmission levers as shown in fig.20.
Grease the lever pins.
The gears of the 180° plate (optional) do not require greasing.
4.
Fit any optional accessories, see the paragraph titled "Accessories”.
4.6 ELECTRICAL CONNECTIONS
1.
Insert
the motor power cable in the previously laid tube
.
2.
Make all the connections with the electrical cabinet, following the in-
structions provided with the cabinet itself.
If the motor cable needs to be extended, provide for shunt boxes
with a protection class IP 67 or greater, inside the supporting box.
Use a cable suitable for outdoor laying, having the proper diameter,
as described in the paragraph "Electrical preparations”.
3.
Insert the plug, fig.21 ref. .
4.
Close the cover of the supporting box, fig.21 ref. .
5.
Screw in the cover using the provided screws.
5. START-UP
1. Programme the control equipment according to need .
2.
Ensure that the automated system is operating correctly.
3. Check that the safety devices operate correctly.
4.
Fill in the maintenance report, contained in the middle of this manual,
and give it to the end user.
5.
Properly train the end user as to the correct operation of the automated
system.
6.
Give the end user the "User's Guide" that is contained in the middle of
the manual.
6. MANUAL OPERATION
1.
Use
the differential switch located upstream from the system to cut
off power .
2.
Open the lock covering the plug, fig.22 ref. .
3. Insert the key and turn it until it stops, fig.22 ref. .
4.
Open the release lever, fig.22 ref. .
5. Manually move the leaf, fig.22 ref. .
6.
Place the release lever back in position.
7. RESTORING NORMAL OPERATION
1.
Use
the differential switch located upstream from the system to cut
off power
.
2. Manually move the leaf until the release device engages, fig.23 ref. .
3.
Place the release lever in rest position, fig.23 ref. .
4. Turn the key until it stops, fig.23 ref. .
5.
Close the protective plug, fig.23 ref. .
6. Ensure that the leaf cannot be moved manually.
7.
Power on the system and perform a few cycles to ensure that the auto-
mated system is operating correctly.
8. AVAILABLE ACCESSORIES
Mechanical limit stops
The mechanical limit stops have been designed to replace the mechanical
beats of the leaf (fig.24).
To install the stops, refer to the related instructions.
The mechanical limit stops cannot be used with the 180° opening
kit.
Kit 180°
This kit lets you obtain a leaf rotation of up to 180° (fig.25).
If this kit is used, you cannot use the mechanical limit stops inside
the box.
To install the kit, refer to the related instructions.
Kit 140°
This kit lets you obtain a leaf rotation of up to 140° (fig.26)
Con l’utilizzo degli arresti meccanici all’interno della cassetta di
fondazione la rotazione dell’anta è limitata a
~
120°.
To install the kit, refer to the related instructions.
Encoder
The encoder is used to detect possible obstacles that prevent normal ope-
ration of the automated system (fig.27 example of installation combined
with kit 180°).
To install the encoder, refer to the related instructions.
Magnetic limit switch
Using this kit - fig.28 - you can determine the leaf stopping point or the
start of the decelerated segment, depending on the characteristics of
the control board used.
Use of the magnetic limit switch requires the use of a control unit
that supports limit switches.
The magnetic limit switch cannot be installed with the 180° kit
and encoder.
To install the kit, refer to the related instructions.
9. MAINTENANCE
Inspect the system every six months , as provided for in current safety
regulations.
The "User's Guide" contains a servicing report form.
10. REPAIRS
Do not make any attempts at repairs and contact only qualified
FAAC S.p.A. personnel and service centres.
11. SPECIAL APPLICATIONS
No special applications have been provided for, any use not described
in this manual is strictly forbidden.